Bedienungsanleitung Makita BFT022F (Seite 6 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598466

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

LED indicator (Fig. 6)

The LED indicator on the tool shows the following functions.

013073

Adjusting the fastening torque (Fig. 7 & 8)

When you wish to drive machine screws, wood screws,

hex bolts, etc. with the predetermined torque, adjusting

the fastening torque as follows.

1. First remove the battery cartridge from the tool.

2. Loosen and remove the screw that secures ring.

3. Rotate the ring in the front of the tool by hand so that a

hole can be seen below the ring.

4. Place the battery cartridge in place and pull the switch

trigger. Release it so that the adjusting ring rotates

and becomes visible in the hole. And then remove the

battery cartridge.

Function Status

Status of the LED indicator/beeper

Action to be

taken

LED indicator Beeper

Auto-stop fastening

This function works when the tool has

reached the preset fastening torque

and normal tightening has been com-

pleted. This helps overtightening to

be avoided.

Lights up in

green for

approximately

one second.

——

Delayed re-start

For approximately one second after

auto-stop fastening, the tool does not

start even if the switch trigger is

pulled.

Warning against

insufficient fastening

Insufficient fastening has been per-

formed when the switch trigger has

released before reaching the preset

fastening torque.

Lights up in red. A long beep

Retighten the

screw.

Warning for battery

cartridge capacity

This indicates the appropriate time to

replace the battery cartridge when

the battery power becomes low.

Flickers in red

slowly.

A series of long

beeps

Replace the

battery with fully

charged one.

Checking the

remaining battery

capacity, Autostop

This function works when the battery

power is almost used up. At this time,

tool stops immediately.

Lights up in red. A long beep

Replace the

battery with fully

charged one.

Check the LED indi-

cator, lamp and

beeper operation

This function works to check the

proper operation of the LED indicator,

lamp and beeper when a battery car-

tridge has been inserted into the tool.

Lights up first in

green, next red.

(And then the

lamp comes

on.)

A series of very

short beeps

—

Anti-reset of control-

ler

This function works when an abnor-

mal drop of the battery voltage occurs

for some reason, and the tool stops.

Flickers in red

and green alter-

natively.

A series of short

beeps

Replace the

battery with fully

charged one.

Overheat

This function works when the temper-

ature of the controller goes up very

highly, and the tool stops.

Flickers in red

quickly.

A series of short

beeps

Remove the

battery car-

tridge immedi-

ately and cool

the tool down.

Operation error of

the switch trigger

This function works to avoid the tool’s

immediate start upon insertion of bat-

tery cartridge into the tool with the

switch trigger being pulled.

Flickers in red

and green alter-

natively.

A series of short

beeps

Release the

switch trigger.

Warning for limit of

the fastening capac-

ity

The tool automatically stops without

the clutch working when exceeding

the fastening capacity limit.

Flickers in red

and green alter-

natively.

A series of short

beeps

Remove the

battery car-

tridge and then

install it again.

Be sure to use

the tool under

load within its

capacity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BFT022F Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita BFT022F

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info