Bedienungsanleitung Makita bft123fz (Seite 8 von 14) (Englisch, Holländisch)

381192

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Adjusting the fastening torque (Fig. 8 & 9)

When you wish to drive machine screws, wood screws,

hex bolts, etc. with the predetermined torque, adjust the

fastening torque as follows.

1. First remove the battery cartridge from the tool.

2. Loosen and remove the screw that secures ring.

3. Rotate the ring in the front of the tool by hand so that a

hole can be seen below the ring.

4. Place the battery cartridge in place and pull the switch

trigger. Release it so that the adjusting ring rotates

and becomes visible in the hole. And then remove the

battery cartridge.

5. Use an optional adjusting grip to adjust the fastening

torque. Insert the pin of the adjusting grip into the hole

in the front of the tool. And then, turn the adjusting grip

clockwise to set a greater fastening torque, and coun-

terclockwise to set a smaller fastening torque.

6. Align the yellow line with your desired number on the

fastening torque scale.

7. Insert the battery cartridge and be sure that a fasten-

ing torque has been set up by using a fastening torque

tester.

8. Rotate the ring in front of the tool and then tighten the

screw to secure the ring.

NOTE:

Numbers on the fastening torque scale is a guideline to

set up your desired fastening torque.

ASSEMBLY

CAUTION:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work on

the tool.

Installing or removing driver bit or socket bit

(Fig. 10 & 11)

Use only the driver bit or socket bit shown in the figure.

Do not use any other driver bit or socket bit.

To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will go.

Then release the sleeve to secure the bit.

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out firmly.

NOTE:

If the bit is not inserted deep enough into the sleeve, the

sleeve will not return to its original position and the bit will

not be secured. In this case, try re-inserting the bit

according to the instructions above.

OPERATION

Screwdriving operation (Fig. 12)

Place the point of the driver bit in the screw head and

apply pressure to the tool. Then switch the tool on. When

the clutch cuts in, the motor will stop automatically. Then

release the switch trigger.

NOTE:

Make sure that the driver bit is inserted straight in the

screw head, or the screw and/or bit may be damaged.

Function Status

Status of

the LED indicator/beeper

Action to be taken

LED indicator Beeper

Checking the

remaining battery

capacity,

Autostop

This function works when the battery

power is almost used up. At this time,

tool stops immediately.

Lights up in

red.

A long beep

Replace the battery

with fully charged

one.

Check the LED

indicator, light and

beeper operation

This function works to check the proper

operation of the LED indicator, light

and beeper when a battery cartridge

has been inserted into the tool.

Lights up first

in green, next

red. (And then

the light

comes on.)

A series of

very short

beeps

Anti-reset of

controller

This function works when an abnormal

drop of the battery voltage occurs for

some reason and the tool stops.

Flickers in red

and green

alternatively.

A series of

short beeps

Replace the battery

with fully charged

one.

Overheat

This function works when the tempera-

ture of the controller goes up very

highly, and the tool stops.

Flickers in red

quickly.

A series of

short beeps

Remove the battery

cartridge immedi-

ately and cool the tool

down.

Operation error of

the switch trigger

This function works to avoid the tool's

immediate start upon insertion of bat-

tery cartridge into the tool with the

switch trigger being pulled.

Flickers in red

and green

alternatively.

A series of

short beeps

Release the switch

trigger.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita bft123fz Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita bft123fz

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info