Bedienungsanleitung Makita bhr 200 sje (Seite 6 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

388967

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

NOTE:

•

The battery charger is for charging Makita-battery cartridge. Never use it for other purposes or for other manufacturer’s

batteries.

•

When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not

accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully

after discharging it completely and recharging a couple of times.

•

If you charge a battery cartridge from a just-operated tool or battery cartridge which has been left in a location exposed to direct

sunlight for a long time, the charging light may flash in red color. If this occurs, wait for a while. Charging will begin after the

battery cartridge is cooled by the cooling fan installed in the charger. When the temperature on battery is more than approx.

70°C, two charging lights may flash in red color, and when approx. 50°C – 70°C, one charging light in red color.

•

If the charging light flashes alternately in green and red color, charging is not possible. The terminals on the charger or battery

cartridge are clogged with dust or the battery cartridge is worn out or damaged.

•

Any of the following conditions indicates damage to the charger and/or battery cartridge.Ask your Makita Authorized or Factory

Service Center to check them.

1) The charging light does not flash (green) when the battery charger is plugged into a power source.

2) The charging light does not light up or flash (red) when the battery is inserted in the charger port.

3) Charging is not completed at even more than two hours after red light comes ON at start of charging.

Battery Type Capacity (mAh) Number of cells Charging time

B2417 1,700 20 Approx. 30 min.

B2430 3,000 20 Approx. 60 min.

Switch action (Fig. 3)

CAUTION:

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the ‘‘OFF’’ position when released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release the

trigger to stop.

Reversing switch action (Fig. 4)

CAUTION:

•

Always check the direction of rotation before operation.

•

Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation before the

tool stops may damage the tool.

•

When not operating the tool, always set the reversing switch

lever to the neutral position.

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A side for

clockwise rotation or from the B side for counterclockwise

rotation. When the switch lever is in the neutral position, the

switch trigger cannot be pulled.

Selecting action mode

Rotation with hammering (Fig. 5)

For drilling in concrete, masonry, etc., depress the lock button

and rotate the change lever so that the pointer points to the

symbol. Use a tungsten- carbide tipped bit.

Rotation only (Fig. 6)

For drilling in wood, metal or plastic materials, depress the

lock button and rotate the change lever so that the pointer

points to the

symbol. Use a twist drill bit or wood bit.

Hammering only (Fig. 7)

For chipping, scaling or demolition operations, depress the

lock button and rotate the change lever so that the pointer

points to the

symbol. Use a bull point, cold chisel, scaling

chisel, etc.

CAUTION:

•

Donotrotatethechangeleverwhenthetoolisrunning.

Thetoolwillbedamaged.

•

Toavoidrapidwearonthemodechangemechanism,be

sure that the change lever is always positively located in

one of the three action mode positions.

Installing or removing bit

Important:

Always be sure that the tool is switched off and the battery

cartridge is removed before installing or removing the bit.

Clean the bit shank and apply the bit grease provided to it

before installing the bit. (Fig. 8)

Insert the bit into the tool. Turn the bit and push it in until it

engages. (Fig. 9)

If the bit cannot be pushed in, remove the bit. Pull the chuck

cover down a couple of times. Then insert the bit again. Turn

the bit and push it in until it engages. (Fig. 10)

After installing, always make sure that the bit is securely held

in place by trying to pull it out.

To remove the bit, pull the chuck cover down all the way and

pull the bit out. (Fig. 11)

Depth gauge (Fig. 12)

The depth gauge is convenient for drilling holes of uniform

depth. Loosen the clamp screw and adjust the depth gauge to

the desired depth. After adjusting, tighten the clamp screw

firmly.

NOTE:

The depth gauge cannot be used at the position where the

depth gauge strikes against the gear housing/motor housing.

Side grip (Fig. 13)

CAUTION:

Always use the side grip to ensure operating safety when

drilling in concrete, masonry, etc.

The side grip swings around to either side, allowing easy

handling of the tool in any position. Loosen the side grip by

turning it counterclockwise, swing it to the desired position and

then tighten it by turning clockwise.

Bit angle

(when chipping, scaling or demolishing)

Important:

Always be sure that the tool is switched off and the battery

cartridge is removed before changing the bit angle.

To change the bit angle, depress the lock button and rotate the

change lever so that the pointer points to the V symbol. Turn

the bit to the desired angle. (Fig. 14)

Depress the lock button and rotate the change lever so that

the pointer points to the

symbol. (Fig. 15)

Then make sure that the bit is securely held in place by turning

it slightly.

Makita bhr 200 sje Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita bhr 200 sje

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info