Bedienungsanleitung Makita BHR262 (Seite 10 von 19) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598562

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

bounce around, uncontrolled. Pressing very hard on the

tool will not increase the efficiency.

Drilling in wood or metal

For Model BHR262, HR262D (Fig. 22 & 23)

Use the optional drill chuck assembly. When installing it,

refer to “Installing or removing the bit” described on the

previous page.

Set the action mode changing knob so that the pointer

points to the symbol.

For Model BHR262T, HR262TD (Fig. 24, 7 & 25)

Use the quick change drill chuck as standard equipment.

When installing it, refer to “changing the quick change

chuck for SDS-plus” described on the previous page.

Hold the ring and turn the sleeve counterclockwise to

open the chuck jaws. Place the bit in the chuck as far as it

will go. Hold the ring firmly and turn the sleeve clockwise

to tighten the chuck. To remove the bit, hold the ring and

turn the sleeve counterclockwise.

Set the action mode changing knob to the symbol.

You can drill up to 13 mm diameter in metal and up to

32 mm diameter in wood.

CAUTION:

• Never use “rotation with hammering” when the drill

chuck assembly is installed on the tool. The drill chuck

assembly may be damaged. Also, the drill chuck will

come off when reversing the tool.

• Pressing excessively on the tool will not speed up the

drilling. In fact, this excessive pressure will only serve

to damage the tip of your bit, decrease the tool

performance and shorten the service life of the tool.

• There is a tremendous twisting force exerted on the

tool/bit at the time of hole breakthrough. Hold the tool

firmly and exert care when the bit begins to break

through the workpiece.

• A stuck bit can be removed simply by setting the

reversing switch to reverse rotation in order to back

out. However, the tool may back out abruptly if you do

not hold it firmly.

• Always secure small workpieces in a vise or similar

hold-down device.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing carbon brushes (Fig. 26)

Remove and check the carbon brushes regularly. Replace

when they wear down to the limit mark. Keep the carbon

brushes clean and free to slip in the holders. Both carbon

brushes should be replaced at the same time. Use only

identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps. (Fig. 27)

Remount the holder cap covers on the tool.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• SDS-Plus Carbide-tipped bits

• Bull point

• Cold chisel

• Scaling chisel

• Grooving chisel

• Drill chuck assembly

• Drill chuck S13

• Chuck adapter

• Chuck key S13

• Bit grease

• Side grip

• Depth gauge

• Blow-out bulb

•Dust cup

• Dust extractor attachment

• Safety goggles

• Plastic carrying case

• Keyless drill chuck

• Makita genuine battery and charger

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Model BHR262, HR262D

Sound pressure level (L

): 91 dB (A)

Sound power level (L

): 102 dB (A)

Uncertainty (K): 3 dB (A)

Model BHR262T, HR262TD

Sound pressure level (L

): 92 dB (A)

Sound power level (L

): 103 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Model BHR262, HR262D

Work mode: hammer drilling into concrete

Vibration emission (a

h,HD

): 13.5 m/s

Uncertainty (K): 1.5 m/s

Work mode: chiselling

Vibration emission (a

h,CHeq

): 11.0 m/s

Uncertainty (K): 1.5 m/s

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BHR262 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info