Bedienungsanleitung Makita BJS100 (Seite 6 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

600757

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Check the smaller clearance with the thickness gauge

and adjust it.

When using the thickness gauge to adjust the blade

clearance, refer to the table.

After adjusting the clearance, tighten the screw securely.

Storing hex wrench (Fig. 6)

Store the hex wrench as shown in the figure when not in

use.

OPERATION

Lubrication (Fig. 7)

Before operation, lubricate the contact point of the center

blade and the pin. To keep good cutting performance, also

use a cutting lubricant from time to time during operation.

OPERATION (Fig. 8)

Turn the tool on and set front ends of the side blades on

the workpiece. Now simply move the tool forward,

keeping the side blades flush with the workpiece surface.

(Fig. 9)

CAUTION:

• When cutting a small portion of the workpiece, you may

have difficulty completing the end of the cut. In that

case, try to cut it again, pulling the workpiece back

slightly.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

NOTICE:

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

The tool and its air vents have to be kept clean. Regularly

clean the tool’s air vents or whenever the vents start to

become obstructed.

Replacing carbon brushes (Fig. 10)

Remove and check the carbon brushes regularly. Replace

when they wear down to the limit mark. Keep the carbon

brushes clean and free to slip in the holders. Both carbon

brushes should be replaced at the same time. Use only

identical carbon brushes.

Insert the top end of slotted bit screwdriver into the notch

in the tool and remove the holder cap cover by lifting it up.

(Fig. 11)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps. (Fig. 12)

Reinstall the holder cap cover on the tool.

Replacing blades

The service life of the blades varies in terms of the

workpiece to be cut. The following reference tables

indicate the approximate service life of the blades.

When the blades become dull, ask Makita Authorized

Service Centers to replace the blades.

For BJS160 and BJS161

For BJS100 and BJS101

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Thickness gauge

• Center blade

• Side blade R

• Side blade L

•Hex wrench

• Various type of Makita genuine batteries and chargers

For Model BJS160

For European countries only

ENG104-1

Noise

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 74 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection.

Vibration

ENG218-2

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: cutting sheet metal

Vibration emission (a

): 12.0 m/s

Uncertainty (K): 1.5 m/s

Workpiece thickness

(mm)

Marking on thickness

gauge

Less than 0.8 0.5

0.8 - 1.3 1.0

More than 1.3 1.5

Material

Cutting thickness

(mm)

Life of blades

(m)

Mild steel plate

(SPCC)

1.6 200

Stainless steel

plate

(SUS304)

1.2 150

Aluminum plate

(A-5052)

2.5 400

Material

Cutting thickness

(mm)

Life of blades

(m)

Mild steel plate

(SPCC)

1.0 120

Stainless steel

plate

(SUS304)

0.7 50

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BJS100 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info