Bedienungsanleitung Makita BMR102 (Seite 10 von 19) (Englisch, Holländisch)

598582

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

3-2. Installing or removing Cluster battery cartridge

(Fig. 5 - 9)

• Pull the supporting bar to allow the battery to insert to

the terminal.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place.

• Release the supporting bar.

• To remove the battery cartridge, pull the supporting bar

and take the battery out of the terminal.

4. Return the battery compartment locker to the original

position.

5. Reduced power, distortion and a “stuttering sound” or

low battery sign that appears on the display are

all the signs that the main battery pack needs to

replace.

Note:

The battery pack can’t be charged via the supplied AC

power adaptor.

6. When low battery sign appears and an “E” keeps

on flashing is the time to replace the back up batteries.

Installing the Soft bended rod

antenna (Fig. 10 & 11)

Install the Soft bended rod antenna as shown in the

figure.

Note:

There is a click in the battery compartment designed to

store the removed antenna.

Using Supplied AC power adaptor

(Fig. 12)

Remove the rubber protector and insert the adaptor plug

into the DC socket on the front side of the radio. Plug the

adaptor into a standard mains socket outlet. Whenever

the adaptor is used, the battery pack is automatically

disconnected. The AC adaptor should be disconnected

from the main supply when not in use.

Note:

When your radio has any interference in AM band by its

adaptor, please move your radio away from its AC

adaptor over 30 cm.

Setting the clock

1. Clock can be set either when the radio is power on or

off.

2. Display will show “-: - -” when the back up batteries

are installed.

3. Long press the time set button for more than

2 seconds, display will flash time set symbol and

also the hour digit, followed by a beep.

4. Rotate Tuning/Volume control knob to set the required

hour.

5. Press button to confirm hour setting, the minute

digit will flash.

6. Rotate Tuning/Volume control knob to set the required

minute.

7. Press the button again to complete clock setting.

Operating the radio

This radio equips with three tuning methods - Scan tuning,

Manual tuning and Memory presets recall.

Scan Tuning

1. Press the Power button to turn on the radio.

2. Select the required waveband by pressing the Band

button. Make sure the rubber bended rod antenna has

been well placed for best FM reception. For AM (MW)

band, rotate the radio to get best signal. Try to avoid to

operate the radio next to computer screen and other

equipment which will cause interference to the radio.

3. Press and release Scan button (long press Scan

button more than 2 seconds will activate time setting),

LCD display will flash Scan symbol and the radio will

search and stop automatically when it finds a radio

station. Press the Scan button again to pick up the

found station.

Note:

A stereo symbol will appear on the display, if the

station found is a stereo station.

Note:

The radio will continue to search next available

stations if you do not press Scan button again when it

finds a radio station.

4. Rotate the Tuning/Volume control knob to get required

sound level. LCD display will show sound level

changes.

Note:

During operating volume control, you can press in

Tuning/Volume control knob to change volume control

to tuning control status.

5. To turn off the radio, press the Power button. Display

will show OFF.

Manual Tuning

1. Press the Power button to turn on the radio.

2. Select the required waveband by pressing the Band

button. Adjust the antenna as described above.

3. A single rotary to the Tuning/Volume control knob will

change the frequency in the following increment:

FM: 50 or 100 kHz

AM (MW): 9 or 10 kHz

Note:

If the radio is in volume control status, press in the

tuning/volume control to become Tuning status.

4. Keep on rotating the Tuning/Volume control knob until

the required frequency shown on the display.

5. Rotate the Tuning/Volume control knob to get required

sound level.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BMR102 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita BMR102

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info