Bedienungsanleitung Makita BO 4565 (Seite 5 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch)

78291

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Installing or removing abrasive paper

NOTE:

Use Makita hook-and-loop sandpaper with this sander.

To attach the sandpaper: (Fig. 2 - 4)

1. Set the tool upside down so that the pad is on top.

2. Position the sandpaper to fit the shape of the base. Be

sure to align the holes on the sandpaper with the

holes on the pad (the dust will be sucked into these

holes; it is therefore important to leave them open).

3. Press the paper firmly over the pad.

To remove the sandpaper:

1. Set the tool upside down so that the sandpaper is on

top.

2. Grasping one corner of the sandpaper, peel it from the

pad.

NOTE:

• If the sandpaper is in good condition, save it for further

use.

When sanding in narrow, hard-to-reach areas (e.g.,

shutters, blinds, louvers), attach the cone-shaped

abrasive papers to the end of the pad (bottom and top).

To sand the end of thin materials, fold the abrasive paper

and attach to the side of the pad as shown in the figures.

Dust bag (accessory) (Fig. 5)

The use of the dust bag makes sanding operations clean

and dust collection easy. To attach the dust bag, fit the

bag’s entry port onto the dust spout on the tool. Make sure

that the hole in the bag’s entry port is just over the pimple-

like protrusion on the dust spout. For the best results,

empty the dust bag when it becomes approximately half

full, tapping it lightly to remove as much dust as possible.

Installing paper dust bag (accessory)

(Fig. 6)

Place the paper dust bag on the paper dust bag holder

with its front side upward. Insert the front fixing cardboard

of the paper dust bag into the groove of the paper dust

bag holder. Then press the upper part of the front fixing

cardboard in arrow direction to hook it onto the claws.

(Fig. 7)

Insert the notch of the paper dust bag into the guide of the

paper dust bag holder. Then install the paper dust bag

holder set on the tool. (Fig. 8 & 9)

OPERATION

Sanding operation (Fig. 10)

CAUTION:

• Never run the tool without the abrasive paper. You may

seriously damage the pad.

• Never force the tool. Excessive pressure may decrease

the sanding efficiency, damage the abrasive paper

and/or shorten tool life.

Hold the tool firmly. Turn the tool on and wait until it

attains full speed. Then gently place the tool on the

workpiece surface. A finishing sander is generally used to

remove only a small amount of material at a time. Since

the quality of the surface is more important than the

amount of stock removed, do not bear down on the tool.

Keep the base flush with the workpiece at all times.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Abrasive paper (without pre-punched holes)

• Paper dust bag

• Paper dust bag holder

• Punch plate

• Dust bag

• Hose 19-2.5

For European countries only

Noise

ENG102-2

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 81 dB (A)

Sound power level (L

): 92 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

Vibration

ENG211-1

The vibration total value (tri-axial vector sum) determined

according to EN60745-2-4:

Work mode: sanding metal plate

Vibration emission (a

): 4 m/s

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BO 4565 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info