78697
5
Zoom out
Zoom in
Vorherige Seite
1/15
Nächste Seite
5
Installing paper dust bag
To install the paper dust bag, place the paper dust bag on
the paper dust bag holder with its front side upward.
Insert the front fixing cardboard of the paper dust bag
into the groove of the paper dust bag holder. (Fig. 6)
Then press the upper part of the front fixing cardboard in
arrow direction to hook it onto the claws. (Fig. 7)
Insert the notch of the paper dust bag into the guide of
the paper dust bag holder. Then install the paper dust
bag holder set on the tool. (Fig. 8 & 9)
Front grip (Fig. 10)
Install the front grip on the tool so that its protrusions fit
into the matching notches in the front of the tool. Secure
the front grip using a screwdriver to tighten the screw
through the hole in the front grip.
Changing pad (Fig. 11)
Makita offers an extensive range of optional super soft
and standard equipped soft pads. Remove the screw
counterclockwise from the center of the base by a sharp
tap with a hammer on the hex wrench. After changing the
pad, tighten the screw clockwise securely.
Switch action (Fig. 12)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the “OFF
position when released.
To start the tool, simply pull the trigger. Release the trig-
ger to stop. For continuous operation, pull the trigger and
then push in the lock button. To stop the tool from the
locked position, pull the trigger fully, then release it.
Speed adjusting dial (Fig. 12)
The tool speed can be infinitely adjusted between
4,000 opm and 10,000 opm by turning the speed adjust-
ing dial, which is marked 1 to 5. Higher speed is obtained
when the dial is turned in the direction of number 5; lower
speed is obtained when it is turned in the direction of
number 1. Refer to the figure below for the relationship
between the number setting on the adjusting dial and the
kind of work.
A range: For polishing
B range: For finish sanding
C range: For regular sanding
NOTE:
The above figure shows standard applications. They may
differ under certain conditions.
Sanding operation (Fig. 13)
CAUTION:
Never switch on the tool when it is in contact with the
workpiece surface, causing an injury to operator.
Never run the tool without the abrasive disc. You may
seriously damage the pad.
Never force the tool. Excessive pressure may decrease
the sanding efficiency, damage the abrasive disc or
shorten tool life.
Turn the tool on and wait until it attains full speed. Then
gently place the tool on the workpiece surface. Keep the
base flush with the workpiece and apply slight pressure
on the tool.
Polishing operation
CAUTION:
Use only a Makita genuine sponge pad, felt pad or wool
pad (optional accessories).
Always operate the tool at low speed to prevent work
surfaces from damage/burning.
Never force the tool. Excessive pressure may decrease
the polishing efficiency and cause motor overload,
resulting in tool malfunction.
1. Applying wax (Fig. 14)
Use an optional sponge pad. Apply wax to the
sponge pad or work surface. Run the tool to smooth
out wax.
NOTE:
First, wax a non critical portion of the work surface to
make sure that the tool will not scratch the surface or
result in uneven waxing.
2. Removing wax (Fig. 15)
Use an optional felt pad. Run the tool to remove
wax.
3. Polishing (Fig. 16)
Use an optional wool pad. Run the tool and apply
the wool pad gently to the work surface.
Orbits per minute
A range
B range
C range
Dial setting
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita BO 6030 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info