Bedienungsanleitung Makita BPJ140 (Seite 7 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598594

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

20. Do not use the tool with damaged guards.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this instruc-

tion manual may cause serious personal injury.

ENC007-8

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using bat-

tery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any conduc-

tive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it

is severely damaged or is completely worn out.

The battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10. Follow your local regulations relating to disposal

of battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the bat-

tery cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tempera-

ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-

tery cartridge cool down before charging it.

4. Charge the battery cartridge once in every six

months if you do not use it for a long period of

time.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before adjusting or checking

function on the tool.

Installing or removing battery cartridge (Fig. 1)

CAUTION:

• Always switch off the tool before installing or removing

of the battery cartridge.

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge. Failure to

hold the tool and the battery cartridge firmly may cause

them to slip off your hands and result in damage to the

tool and battery cartridge and a personal injury.

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip it

into place. Insert it all the way until it locks in place with a

little click. If you can see the red indicator on the upper

side of the button, it is not locked completely.

CAUTION:

• Always install the battery cartridge fully until the red

indicator cannot be seen. If not, it may accidentally fall

out of the tool, causing injury to you or someone

around you.

• Do not install the battery cartridge forcibly. If the car-

tridge does not slide in easily, it is not being inserted

correctly.

Battery protection system (Fig. 2)

The tool is equipped with a battery protection system.

This system automatically cuts off power to the motor to

extend battery life.

The tool will automatically stop during operation if the

tool and/or battery are placed under one of the following

conditions:

• Overloaded:

The tool is operated in a manner that causes it to draw

an abnormally high current.

In this situation, turn the tool off and stop the applica-

tion that caused the tool to become overloaded. Then

turn the tool on to restart.

If the tool does not start, the battery is overheated. In

this situation, let the battery cool before turning the tool

on again.

• Low battery voltage:

The remaining battery capacity is too low and the tool

will not operate. In this situation, remove and recharge

the battery.

NOTE:

• The overheat protection works only with a battery car-

tridge with a star mark.

Indication lamp with multi function (Fig. 3)

Indication lamps are located in two positions.

When the battery cartridge is inserted on the tool with the

slide switch positioned in the “O (OFF)” position, the indi-

cation lamp flickers quickly for approximately one sec-

ond. If it does not flicker so, the battery cartridge or

indication lamp has broken.

– Overload protection

– When the tool is overloaded, the indication lamp

lights up. When the load on the tool is reduced, the

lamp goes out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BPJ140 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info