Bedienungsanleitung Makita BTD 132 (Seite 6 von 52) (Dänisch, Portugiesisch, Spanisch)

598616

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Changing the hammering force (Fig. 6)

The hammering force can be changed in three steps:

hard, medium and soft.

This allows a tightening suitable to the work.

Every time the hammering force button is pressed,

the number of blows changes in three steps.

For approximately one minute after releasing the switch

trigger, the hammering force can be changed.

NOTE:

• When all lamps on the switch panel go out, the tool is

turned off to save the battery power. The hammer force

grade can be checked by pulling the switch trigger to

the extent that the tool does not operate.

• During the operation of switch trigger, the hammer

force grade cannot be changed.

Empty signal for remaining battery capacity (Fig. 7)

Pulling the trigger switch when the remaining battery

capacity becomes very low makes LED indicator lights

up.

If the tool is used continuously with the LED indicator

lighting up and the battery power is almost used up, the

LED indicator will flicker and the tool itself will stop.

Please refer to the following table for the LED indicator

status and the remaining battery capacity.

NOTE:

• When all lamps on the switch panel go out, the tool is

turned off to save the battery power. The remaining

battery capacity can be checked by pulling the switch

trigger to the extent that the tool does not operate.

• All of the lamps on the switch panel go out approxi-

mately one minute after releasing the switch trigger.

• If the LED indicator flickers and the tool stops even with

a recharged battery cartridge, stop using and have the

tool repaired by a Makita local service center.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing driver bit or socket bit

Use only the driver bit or socket bit shown in the figure.

(Fig. 8)

Do not use any other driver bit or socket bit.

For tool without one-touch type (Fig. 9)

To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will go.

Then release the sleeve to secure the bit.

For tool with one-touch type (Fig. 10)

To install the bit, insert the bit into the sleeve as far as it

will go.

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out firmly.

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

• When it is difficult to insert the bit, pull the sleeve and

insert it into the sleeve as far as it will go.

• After inserting the bit, make sure that it is firmly

secured. If it comes out, do not use it.

Hook (Fig. 11)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool hous-

ing on either side and then secure it with a screw.

To remove, loosen the screw and then take it out.

Hammering force grade

displayed on panel

Maximum blows Application Work

Hard

3,200 (min

–1

)

Tightening when force and speed

are desired.

Tightening in underwork material/

Tightening long screws/

Tightening bolts.

Medium

2,600 (min

–1

)

Tightening when a good finishing

is needed.

Tightening in the finishing board,

plaster board.

Soft

1,100 (min

–1

)

Tightening when excessive

tightening need to be avoided

because of potentially clogged

female screw and broken or

damaged screw head.

Tightening sash screw/

Tightening small screws

such as M6.

LED indicator status Remaining battery capacity

OFF

Enough

Lighting on

20%

Flickering

The light also flickers

three times a second at

the same time.

Very low and the tool will

stop.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BTD 132 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita BTD 132

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info