Bedienungsanleitung Makita BTD 150 (Seite 3 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

598624

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ENGLISH

Explanation of general view

1 Red part

2 Button

3 Battery cartridge

4 Terminal cover

5 Charging lights

6 Battery charger

7 Bit

8 Sleeve

9 Switch trigger

10 Reversing switch lever

11 A side

12 B side

13 Clockwise

14 Counterclockwise

15 Wood screw size

16 Seconds

17 Fastening time

18 Limit mark

19 Brush holder cap

20 Screwdriver

SPECIFICATIONS

Model BTD150

Capacities

Machine screw ............................................ 4 mm – 10 mm

Self drilling screw ......................................... 4 mm–6mm

No load speed (min

–1

) ............................................ 0 – 2,300

Impacts per minute ................................................. 0 – 3,000

Overall length ............................................................ 190 mm

Net weight .................................................................... 1.8 kg

Rated voltage ...................................................... D.C. 14.4 V

•

Due to our continuing program of research and develop-

ment, the specifications herein are subject to change with-

out notice.

•

Note: Specifications may differ from country to country.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

IMPORTANT SAFETY INSTRUCTIONS

FOR CHARGER & BATTERY CARTRIDGE

ENC002-3

1. SAVE THESE INSTRUCTIONS — This manual con-

tains important safety and operating instructions for

battery charger.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger, (2)

battery, and (3) product using battery.

3. CAUTION — To reduce risk of injury, charge only

MAKITA type rechargeable batteries. Other types of

batteries may burst causing personal injury and dam-

age.

4. Do not expose charger to rain or snow.

5. Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a risk

of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord,

pull by plug rather than cord when disconnecting

charger.

7. Make sure cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage or stress.

8. Do not operate charger with damaged cord or

plug — replace them immediately.

9. Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way; take

it to a qualified serviceman.

10. Do not disassemble charger or battery cartridge; take

it to a qualified serviceman when service or repair is

required. Incorrect reassembly may result in a risk of

electric shock or fire.

11. To reduce risk of electric shock, unplug charger from

outlet before attempting any maintenance or clean-

ing. Turning off controls will not reduce this risk.

12. The battery charger is not intended for use by young

children or infirm persons without supervision.

13. Young children should be supervised to ensure that

they do not play with the battery charger.

14. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk of

overheating, possible burns and even an explosion.

15. If electrolyte gets into your eyes, rinse them out with

clear water and seek medical attention right away. It

may result in loss of your eyesight.

ADDITIONAL SAFETY RULES FOR CHARGER

& BATTERY CARTRIDGE

1. Do not charge battery cartridge when temperature is

BELOW 10°C (50°F) or ABOVE 40°C (104°F).

2. Do not attempt to use a step-up transformer, an

engine generator or DC power receptacle.

3. Do not allow anything to cover or clog the charger

vents.

4. Do not short the battery cartridge:

(1) Do not touch the terminals with any conductive

material.

(2) Avoid storing battery cartridge in a container with

other metal objects such as nails, coins, etc.

(3) Do not expose battery cartridge to water or rain.

A battery short can cause a large current flow, over-

heating, possible burns and even a breakdown.

5. Do not store the tool and battery cartridge in loca-

tions where the temperature may reach or exceed

50°C (122°F).

6. Do not incinerate the battery cartridge even if it is

severely damaged or is completely worn out. The

battery cartridge can explode in a fire.

7. Be careful not to drop, shake or strike battery.

8. Do not charge inside a box or container of any kind.

The battery must be placed in a well ventilated area

during charging.

ADDITIONAL SAFETY RULES

FOR TOOL

ENB024-1

1. Be aware that this tool is always in an operating

condition, because it does not have to be plugged

into an electrical outlet.

2. Hold tool by insulated gripping surfaces when per-

forming an operation where the cutting tool may

contact hidden wiring. Contact with a ‘‘live’’ wire will

also make exposed metal parts of the tool ‘‘live’’ and

shock the operator.

3. Always be sure you have a firm footing.

Be sure no one is below when using the tool in high

locations.

4. Hold the tool firmly.

5. Wear ear protectors.

SAVE THESE INSTRUCTIONS.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BTD 150 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info