Bedienungsanleitung Makita BTD134 (Seite 7 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598619

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Empty signal for remaining battery capacity (Fig. 6)

Stop the tool and with the tool stopped press the button

on the switch panel and the remaining battery capacity

will be signaled on the panel.

The status displayed on the switch panel and the remain-

ing battery capacity is shown in the following table.

NOTE:

• Before checking the remaining battery capacity, be

sure to stop the tool.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing driver bit or socket bit

Use only bits that has inserting portion shown in the fig-

ure. (Fig. 7)

For tool with shallow bit hole

For tool with deep bit hole

1. To install the bit, pull the sleeve and insert the bit into

the sleeve as far as it will go. (Fig. 8)

2. To install the bit, insert the bit-piece and bit into the

sleeve as far as it will go. The bit-piece should be

inserted into the sleeve with its pointed end facing

in. Then release the sleeve to secure the bit. (Fig. 9)

To remove the bit, pull the sleeve and pull the bit out.

NOTE:

• For all countries other than Europe, it's not necessary

to pull the sleeve when installing the bit.

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

• When it is difficult to insert the bit, pull the sleeve and

insert it into the sleeve as far as it will go.

• After inserting the bit, make sure that it is firmly

secured. If it comes out, do not use it.

Hook (Fig. 10)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool hous-

ing on either side and then secure it with a screw. To

remove, loosen the screw and then take it out.

OPERATION

The proper fastening torque may differ depending upon

the kind or size of the screw/bolt, the material of the

workpiece to be fastened, etc. The relation between fas-

tening torque and fastening time is shown in the figures.

(Fig. 11, 12 & 13)

Hold the tool firmly and place the point of the driver bit in

the screw head. Apply forward pressure to the tool to the

extent that the bit will not slip off the screw and turn the

tool on to start operation.

NOTE:

• Use the proper bit for the head of the screw/bolt that

you wish to use.

• When fastening screw M8 or smaller, carefully adjust

pressure on the switch trigger so that the screw is not

damaged.

• Hold the tool pointed straight at the screw.

• If you tighten the screw for a time longer than shown in

the figures, the screw or the point of the driver bit may

be overstressed, stripped, damaged, etc. Before start-

ing your job, always perform a test operation to deter-

mine the proper fastening time for your screw.

• If you use a spare battery to continue the operation,

rest the tool at least 15 min.

The fastening torque is affected by a wide variety of fac-

tors including the following. After fastening, always check

the torque with a torque wrench.

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening

torque will be reduced.

2. Driver bit or socket bit

Failure to use the correct size driver bit or socket bit

will cause a reduction in the fastening torque.

3. Bolt

• Even though the torque coefficient and the class of

bolt are the same, the proper fastening torque will

differ according to the diameter of bolt.

• Even though the diameters of bolts are the same,

the proper fastening torque will differ according to

the torque coefficient, the class of bolt and the bolt

length.

4. The manner of holding the tool or the material of

driving position to be fastened will affect the torque.

5. Operating the tool at low speed will cause a reduc-

tion in the fastening torque.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before attempting to perform

inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

LED indicator status Remaining battery capacity

About 50% or more

About 20% - 50%

About less than 20%

A = 12 mm

B = 9 mm

Use only these type of bit. Follow the

procedure (1).

(Note) Bit-piece is not necessary.

A = 17 mm

B = 14 mm

To install these types of bits, follow the

procedure (1).

A = 12 mm

B = 9 mm

To install these types of bits, follow the

procedure (2).

(Note) Bit-piece is necessary for

installing the bit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BTD134 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info