Bedienungsanleitung Makita BTP 140 (Seite 8 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

78893

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Selecting the action mode

This tool employs an action mode changing lever. Select

one of the four modes suitable for your work needs by

using this lever.

For rotation with impact, turn the lever so that the arrow

on the lever points toward the mark on the tool body.

(Fig. 5)

For rotation with hammering, turn the lever so that the

arrow points toward the mark on the tool body.

(Fig. 6)

For rotation with clutch, turn the lever so that the arrow

points toward the mark on the tool body. (Fig. 7)

For rotation only, turn the lever so that the arrow on the

lever points toward the mark or the mark on the

tool body. (Fig. 8)

Sliding to the mark is for high rotation and the

mark is for low rotation. (Fig. 9)

Before operation, always make sure that the lever is cor-

rectly set to your desired mode mark and use the tool at

an appropriate speed for your work.

CAUTION:

• When using the action mode change lever, use only

when the tool stops. But when the lever does not easily

move, pull the switch trigger slightly to rotate the spin-

dle and then move the lever.

• Always set the lever correctly to your desired mode

mark. If you operate the tool with the lever positioned

halfway between the mode marks, the tool may be

damaged.

Adjusting the fastening torque (Only for

screwdriving operation mode

) (Fig. 10)

The fastening torque can be adjusted in 16 steps by turn-

ing the adjusting ring so that its graduations are aligned

with the pointer on the tool body. The fastening torque is

minimum when the number 1 is aligned with the pointer,

and maximum when the number 16 is aligned with the

pointer.

The clutch will slip at various torque levels when set at

the number 1 to 16.

Before actual operation, drive a trial screw into your

material or a piece of duplicate material to determine

which torque level is required for a particular application.

NOTE:

• In modes other than screwdriving mode, the adjusting

ring can be placed at any position because it does not

work.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing driver bit or socket bit

Use only the driver bit or socket bit shown in the figure.

Do not use any other driver bit or socket bit. (Fig. 11)

For European and North & South American coun-

tries, Australia and New Zealand

For other countries

1. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will

go. Then release the sleeve to secure the bit.

(Fig. 12)

2. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit-piece and bit into the sleeve

as far as it will go. The bit-piece should be inserted

into the sleeve with its pointed end facing in. Then

release the sleeve to secure the bit. (Fig. 13)

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out firmly.

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

Hook (Accessory) (Fig. 14)

CAUTION:

• When installing the hook, tighten the screw firmly. Fail-

ure to do so may cause the breakage of the tool or per-

sonal injury.

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool hous-

ing on either side and then secure it with a screw. To

remove, loosen the screw and then take it out.

OPERATION

CAUTION:

• Always insert the battery cartridge all the way until it

locks in place. If you can see the red part on the upper

side of the button, it is not locked completely. Insert it

fully until the red part cannot be seen. If not, it may

accidentally fall out of the tool, causing injury to you or

someone around you.

Impact driver operation

When driving wood screws or bolts, set the action mode

changing lever to the mark. The adjusting ring can be

placed at any position.

Screwdriving (Fig. 15)

Hold the tool firmly and place the point of the driver bit in

the screw head. Apply forward pressure to the tool to the

extent that the bit will not slip off the screw and turn the

tool on to start operation.

A = 12 mm

B = 9 mm

Use only these type of bit. Follow the

procedure (1).

(Note)

Bit-piece is not necessary.

A = 17 mm

B = 14 mm

To install these types of bits, follow the

procedure (1).

(Note)

Makita bits are these types.

A = 12 mm

B = 9 mm

To install these types of bits, follow the

procedure (2).

(Note)

Bit-piece is necessary for installing the

bit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BTP 140 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info