Bedienungsanleitung Makita BTP141 (Seite 9 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598664

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

NOTE:

• When the LED display goes off, the tool is turned off to

save the battery power. To check the remaining battery

capacity, slightly pull the switch trigger.

• The LED display goes off approximately one minute

after releasing the switch trigger.

• When the temperature of the tool gets high, the light

flashes once per second for one minute, and then the

LED display goes off. In this case, cool down the tool

before operation.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing driver/drill/socket bit

(Fig. 11)

Use only the driver/drill/socket bit shown in the figure. Do

not use any other driver/drill/socket bit.

For tool with shallow bit hole

For tool with deep bit hole

1. To install the bit, pull the sleeve and insert the bit into

the sleeve as far as it will go. Then release the

sleeve to secure the bit. (Fig. 12)

2. To install the bit, insert the bit-piece and bit into the

sleeve as far as it will go. The bit-piece should be

inserted into the sleeve with its pointed end facing

in. Then release the sleeve to secure the bit. (Fig.

13)

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out firmly.

CAUTION:

• Do not touch the drill bit shortly after operating as it

gets hot. Replace the drill bit after cooling it down.

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

• After inserting the bit, make sure that it is firmly

secured. If it comes out, do not use it.

Hook (optional accessory) (Fig. 14)

CAUTION:

• When installing the hook, tighten the screw firmly. Fail-

ure to do so may cause the breakage of the tool or per-

sonal injury.

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool hous-

ing on either side and then secure it with a screw. To

remove, loosen the screw and then take it out.

OPERATION (Fig. 15)

CAUTION:

• Always insert the battery cartridge all the way until it

locks in place with a little click. If you can see the red

indicator on the upper side of the button, it is not locked

completely. Install it fully until the red indicator cannot

be seen. If not, it may accidentally fall out of the tool,

causing injury to you or someone around you.

• If the tool is operated continuously until the battery car-

tridge has discharged, allow the tool to rest for 15 min-

utes before proceeding with a fresh battery.

Impact driver mode “ ”

Screwdriving

Hold the tool firmly and place the point of the driver bit in

the screw head. Apply forward pressure to the tool to the

extent that the bit will not slip off the screw and turn the

tool on to start operation.

Tightening bolts (Fig. 16 & 17)

The proper fastening torque may differ depending upon

the kind or size of the screw/bolt, the material of the

workpiece to be fastened, etc. The relation between fas-

tening torque and fastening time is shown in the figures.

NOTE:

• When the action mode is set to impact driver mode,

make sure that the tool impacts properly by fastening a

wood screw before operation. If the tool does not work

properly, contact your nearest Makita service center.

• Hold the tool pointed straight at the screw.

• Use the proper bit for the head of the screw/bolt that

you wish to use.

• When fastening screw M8 or smaller, carefully adjust

pressure on the switch trigger so that the screw is not

damaged.

• If you tighten the screw for a time longer than shown in

the figures, the screw or the point of the driver bit may

be overstressed, stripped, damaged, etc. Before start-

ing your job, always perform a test operation to deter-

mine the proper fastening time for your screw.

The fastening torque is affected by a wide variety of fac-

tors including the following. After fastening, always check

the torque with a torque wrench.

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening

torque will be reduced.

2. Driver bit or socket bit

Failure to use the correct size driver bit or socket bit

will cause a reduction in the fastening torque.

3. Bolt

• Even though the torque coefficient and the class of

bolt are the same, the proper fastening torque will

differ according to the diameter of bolt.

• Even though the diameters of bolts are the same,

the proper fastening torque will differ according to

the torque coefficient, the class of bolt and the bolt

length.

4. The manner of holding the tool or the material of

driving position to be fastened will affect the torque.

5. Operating the tool at low speed will cause a reduc-

tion in the fastening torque.

A = 12 mm

B = 9 mm

Use only these type of bit. Follow the

procedure (1).

(Note) Bit-piece is not necessary.

A = 17 mm

B = 14 mm

To install these types of bits, follow the

procedure (1).

A = 12 mm

B = 9 mm

To install these types of bits, follow the

procedure (2).

(Note) Bit-piece is necessary for install-

ing the bit.

Makita BTP141 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info