Bedienungsanleitung Makita btw200 (Seite 8 von 88) (Deutsch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

381209

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

– High tensile bolt –

CAUTION:

•

Always insert the battery cartridge all the way until it

locks in place. If you can see the red part on the

upper side of the button, it is not locked completely.

Insert it fully until the red part cannot be seen. If not,

it may accidentally fall out of the tool, causing injury

to you or someone around you.

•

When operating overhead, make sure the battery

cartridge is locked securely so that it will not be

fallen out of the tool. If not, it may accidentally fall

out of the tool, causing injury to you or someone

around you.

Hold the tool firmly and place the socket over the bolt

or nut. Turn the tool on and fasten for the proper

fastening time.

NOTE:

•

Hold the tool pointed straight at the bolt or nut

without applying excessive pressure on the tool.

•

Excessive fastening torque may damage the bolt or

nut. Before starting your job, always perform a test

operation to verify the adequate fastening speed

and time for your bolt or nut.

The fastening torque is affected by a wide variety of

factors including the following. After fastening, always

check the torque with a torque wrench.

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening

torque will be reduced.

2. Socket

•

Failure to use the correct size socket will cause

a reduction in the fastening torque.

•

A worn socket (wear on the hex end or square

end) will cause a reduction in the fastening

torque.

3. Bolt

•

Even though the torque coefficient and the class

of bolt are the same, the proper fastening torque

will differ according to the diameter of the bolt.

•

Even though the diameters of bolts are the

same, the proper fastening torque will differ

according to the torque coefficient, the class of

bolt and the bolt length.

4. The use of the universal joint or the extension bar

somewhat reduces the fastening force of the

impact wrench. Compensate by fastening for a

longer period of time.

5. Type of materials to be fastened, the manner of

holding the tool and the tool speed will affect the

torque.

CAUTION:

If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

15 minutes before proceeding with a fresh battery.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Replacement of carbon brushes (Fig.8&9)

Replace carbon brushes when they are worn down to

the limit mark. Both identical carbon brushes should

be replaced at the same time.

To maintain product safety and reliability, repairs,

maintenance or adjustment should be carried out by a

Makita Authorized Service Center.

Proper fastening torque for M16

M16 x 50 at high speed

M12x50at

high speed

M16 x 50 at low speed

Proper fastening torque for M12

M12 x 50 at low speed

Proper fastening torque for M10

M10 x 50 at low speed

M10 x 50 at high speed

Seconds

Fastening time

Fastening torque

BTW200 (Eng) (’100. 10. 27)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita btw200 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita btw200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info