Bedienungsanleitung Makita BUC250 (Seite 18 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

476836

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

2. Press the lever and with the lever pressed in, turn it

counterclockwise to loosen the nut until sprocket

cover comes off. (Pressing in the lever leads to the

fitting of lever into the nut.) (Fig. 7)

3. Turn the adjusting dial counterclockwise to release

the saw chain tension.

4. Remove the sprocket cover.

5. Remove the saw chain and guide bar from the chain

saw.

6. To install the saw chain, fit in one end of the saw

chain on the top of the guide bar and the other end

of it around the sprocket. (Fig. 8)

At this time, fit the saw chain as shown in the figure

because it rotates in the direction of arrow.

7. Rest the guide bar in place on the chain saw.

8. Turn the adjusting dial counterclockwise to slide the

adjusting pin in the direction of arrow. (Fig. 9)

9. Place the sprocket cover on the chain saw so that

the adjusting pin is positioned in a small hole in the

guide bar. (Fig. 10)

10. Press in the lever and with the lever depressed turn

it fully clockwise to tighten the nut. Then make it

about a quarter turn counterclockwise to loosen the

nut lightly. (Fig. 11)

Adjusting saw chain tension

The saw chain may become loose after many hours of

use. From time to time check the saw chain tension

before use. (Fig. 12)

Move the lever in the upright position.

Press in the lever. With the lever depressed, make a

quarter turn on it counterclockwise to loosen the nut

lightly. (Pressing in the lever leads to the fitting of lever

into the nut.) (Fig. 13)

Turn the adjusting dial to adjust saw chain tension. Grasp

the saw chain in the middle of the guide bar and lift up.

The gap between the guide bar and the tie strap of the

saw chain should be approx. 2 – 4 mm. If the gap is not

approx. 2 – 4 mm, slightly turn the adjusting dial which

secures the guide bar. At this time, adjust with the tip of

guide bar slightly pointing up. (Fig. 14)

With the lever depressed, turn it fully clockwise to tighten

the nut firmly. (Fig. 15)

Return the lever to its original position. (Fig. 16)

CAUTION:

• Excessively high tension of saw chain may cause

breakage of saw chain, wear of the guide bar and

breakage of the adjusting dial.

• Installing or removing saw chain should be carried out

in a clean place free from sawdust and the like.

OPERATION

Lubrication (Fig. 17)

Saw chain is automatically lubricated when the tool is in

operation.

Check the amount of remaining oil in the oil tank through

the oil inspection window.

To refill the tank, remove the cap from the oil tank open-

ing. The oil tank capacity is 80 ml.

After refilling the tank, always screw the provided oil tank

cap on the chain saw.

CAUTION:

• When filling the chain saw with chain oil for the first

time, or refilling the tank after it has been completely

emptied, add oil up to the bottom edge of the filler neck.

The oil delivery may otherwise be impaired.

• As a saw chain oil, use oil exclusively for Makita chain

saws or oil available in market.

• Never use oil including dust and particles or volatile oil.

• When pruning trees, use botanical oil. Mineral oil may

harm trees.

• Never force the chain saw when pruning trees.

• Before cutting out, make sure that the provided oil tank

cap is screwed in place.

Hold the chain saw away from the tree. Start it and wait

until lubrication on saw chain is adequate.

Bring the lower guide into contact with the branch to be

cut before switching on. Cutting without bringing the

lower guide into contact with the branch may cause the

guide bar to wobble, resulting in injury to operator.

Saw the wood to be cut by just moving it down. (Fig. 18)

WORKING WITH THE CHAIN SAW

The first time user should, as a minimum practice, do cut-

ting logs on a saw-horse or cradle.

Pruning trees

CAUTION:

• Keep all parts of the body away from the saw chain

when the motor is operating.

• Hold the chain saw firmly with both hands when the

motor is running.

• Do not overreach. Keep proper footing and balance at

all times.

Bring the lower guide into contact with the branch to be

cut before switching on. Cutting without bringing the

lower guide into contact with the branch may cause the

guide bar to wobble, resulting in injury to operator.

(Fig. 19)

When cutting thick branches, first make a shallow under-

cut and then make the finish cut from the top. (Fig. 20)

If you try to cut off thick branches from the bottom, the

branch may close in and pinch the saw chain in the cut. If

you try to cut off thick branches from the top without a

shallow undercut, the branch may splinter. (Fig. 21)

If you cannot cut the timber right through with a single

stroke:

Apply light pressure to the handle and continue sawing

and draw the chain saw back a little; then apply the spike

a little lower and finish the cut by raising the handle.

(Fig. 22)

Bucking

For bucking cuts, rest the serrated rail shown in the figure

on the wood to be cut. (Fig. 23)

With the saw chain running, saw into the wood, using the

top handle to raise the saw and the front one to guide it.

Use the serrated rail as a pivot.

Continue the cut by applying slight pressure to the front

handle, easing the saw back slightly. Move the serrated

rail further down the timber and raise the front handle

again.

When making several cuts, switch the chain saw off

between cuts.

Makita BUC250 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info