Bedienungsanleitung Makita CC300D (Seite 7 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600678

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Installing or removing diamond wheel

(Fig. 6)

CAUTION:

• When installing the diamond wheel, be sure to tighten

the bolt securely.

• Use only the Makita wrench to install or remove the

diamond wheel.

To remove the diamond wheel, press the shaft lock fully

so that the diamond wheel cannot revolve and use the

wrench to loosen the hex bolt counterclockwise. Then

remove the hex bolt, outer flange and diamond wheel.

(Fig. 7)

To install the diamond wheel, follow the removal

procedure in reverse. Always install the diamond wheel so

that the arrow on the diamond wheel points in the same

direction as the arrow on the diamond wheel case.

BE SURE TO TIGHTEN THE HEX BOLT SECURELY.

(Fig. 8)

NOTE:

• If a inner flange is removed by chance, install the inner

flange so that its protrusion (bigger side) faces inside

as shown in the figure.

Hex wrench storage (Fig. 9)

When not in use, store the hex wrench as shown in the

figure to keep it from being lost.

Installing water supply

Loosen the screw A. Slide the tank holder all the way over

the motor housing. Position the notch of the tank holder

positions just below the screw head as illustrated. Then

tighten the screw A. (Fig. 10)

Attach the tank on the tank holder so that the tank holder

fits between the step and dots. Connect the cap on the

tube end to the mouth of the tank. Turn the tank

clockwise. Then tighten the screw B. (Fig. 11)

Water supply (Fig. 12 & 13)

Be sure that the water supply cock is closed before filling

the tank with water. Open the cap on the tank and fill the

water. Recap the tank.

CAUTION:

• When filling the tank with water, be careful not to let the

tool get wet.

OPERATION (Fig. 14)

Hold the tool firmly. Set the base plate on the workpiece to

be cut without the wheel making any contact. Then turn

the tool on and wait until the wheel attains full speed.

Feed water to the wheel by adjusting the water supply

cock to obtain a gentle flow of water. Move the tool

forward over the workpiece surface, keeping it flat and

advancing smoothly until the cutting is completed. Keep

your cutting line straight and your speed of advance

uniform.

For fine, clean cuts, cut slowly. (When cutting glass plate

5 mm thick, cut at about 250 mm/min. When cutting tile

10 mm thick, cut at about 300 mm/min.) Also slow down

as you complete a cut to avoid breaking or cracking the

workpiece being cut.

CAUTION:

• Be sure to hold the workpiece firmly down on a stable

bench or table during operation.

• Do not twist or force the tool in the cut, or the motor

may be overloaded or the workpiece may break.

• Do not use the tool with the diamond wheel in an

upward or sideways position.

• The wheel for this tool is a wet-type diamond wheel for

glass and tile applications. Be sure to feed water to the

diamond wheel during operation.

• If the cutting action of the diamond wheel begins to

diminish, dress the cutting edge of the wheel using an

old discarded coarse grit bench grinder wheel or

concrete block. Dress by pressing lightly on the outer

edge of the diamond wheel.

NOTE:

• When the battery cartridge temperature is low, the tool

may not work to its full capacity. At this time, for

example, use the tool for a light-duty cut for a while

until the battery cartridge warms up as high as room

temperature. Then, the tool can work to its full capacity.

• Make sure that the water supply cock is closed before

operation.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Diamond wheels

•Hex wrench

• Various type of Makita genuine batteries and chargers

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ from

country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 89 dB (A)

Sound power level (L

): 100 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita CC300D Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info