Bedienungsanleitung Makita DA 4031 (Seite 5 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448290

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

ENGLISH

Explanation of general view

1Tighten

2 Chuck key

3 Side grip

4 Spade grip

5 Wrench holder

6 Loosen

7Hex wrench

8 U mark

9 Motor housing

10 Lock button

11 Handle

12 Press

13 Switch trigger

14 Reversing switch lever

15 A side

16 Clockwise

17 B side

18 Counterclockwise

19 Speed change knob

20 Pointer

21 Lock button

22 Reaction

23 Forward

24 Drilling in forward bit turns

clockwise

25 Reverse

26 Reversing bit turns

counterclockwise

27 Limit mark

28 Screwdriver

29 Brush holder cap

SPECIFICATIONS

Model DA4030 DA4031

Drilling capacities

Wood

Auger-bit .................................................................................38 mm 38 mm

Self-feed bit.............................................................................65 mm High: 65 mm

Low: 118 mm

Hole saw ................................................................................. — 152 mm

Steel ..........................................................................................13 mm 13 mm

No load speed (min

-1

)...................................................................1,200 High: 1,200

Low: 300

Overall length ...............................................................................417 mm 462 mm

Overall length (with an extended spade grip) ...............................491 mm 536 mm

Net weight.....................................................................................4.8 kg 5.6 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES

ENB001-1

1. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tools

may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the ope-

ator.

2. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

3. Hold the tool firmly.

4. Keep hands away from rotating parts.

5. Do not leave the tool running. Operate the tool

only when hand-held.

6. Do not touch the drill bit or the workpiece imme-

diately after operation; they may be extremely

hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing drill bit (Fig. 1)

CAUTION:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

To install the bit, place it in the chuck as far as it will go.

Tighten the chuck by hand. Place the chuck key in each

of the three holes and tighten clockwise. Be sure to

tighten all three chuck holes evenly. To remove the bit,

turn the chuck key counterclockwise in just one hole,

then loosen the chuck by hand. After using the chuck key,

be sure to return it to the original position.

Installing side grip (auxiliary handle) (Fig. 2)

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing the side grip.

• Always be sure that the side grip is installed securely.

Screw the side grip on the tool securely. The side grip

can be installed on either side of the tool.

Spade grip (Fig. 3 & 4)

The spade grip can be installed in any position as shown

in the figure. To change the position, loosen the hex bolts

(both sides) with a hex wrench and turn the spade grip to

the desired position. Then tighten the hex bolts securely.

After reposition the grip, return the hex wrench to the

wrench holder.

CAUTION:

• Do not fix the spade grip beyond the limits of the arrow.

Be cautious that your hand is not caught in the grip.

Keep the hand away from the drill chuck. They can lead

to serious accidents.

• Always be sure that the hex bolts (both sides) of the

spade grip are tightened securely.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DA 4031 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita DA 4031

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info