Bedienungsanleitung Makita DA301D (Seite 5 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

600654

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

8. Be careful not to drop, shake or strike battery.

9. Do not charge inside a box or container of any

kind. The battery must be placed in a well

ventilated area during charging.

ADDITIONAL SAFETY RULES

FOR MACHINE

1. Be aware that this machine is always in an

operating condition, because it does not have

to be plugged into an electrical outlet.

2. Always be sure you have a firm footing. Be

sure no one is below when using the machine

in high locations.

3. Hold the machine firmly.

4. Keep hands away from rotating parts.

5. When drilling into walls, floors or wherever

‘‘live’’electrical wires may be encountered, DO

NOT TOUCH ANY METAL PARTS OF THE

MACHINE! Hold the machine by the insulated

grasping surfaces to prevent electric shock if

you drill into a ‘‘live’’ wire.

6. Do not leave the machine running. Operate the

machine only when hand-held.

7. Do not touch the drill bit or the workpiece

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge

(Fig. 1)

•

Always switch off the machine before insertion or

removal of the battery cartridge.

•

To remove the battery cartridge, pull out the set

plate on the machine and grasp both sides of the

cartridge while withdrawing it from the machine.

•

To insert the battery cartridge, align the tongue on

the battery cartridge with the groove in the housing

and slip it into place. Snap the set plate back into

place. Be sure to close the set plate fully before

using the machine to prevent the battery cartridge

from accidentally falling out of the machine.

•

Do not use force when inserting the battery car-

tridge. If the cartridge does not slide in easily, it is

not being inserted correctly.

Charging

For DA301D/DA391D (Fig. 2)

1. Plug the battery charger into your power source.

2. Insert the battery cartridge so that the plus and

minus terminals on the battery cartridge are on the

same sides as their respective markings on the

battery charger. Insert the cartridge fully into the

port so that it rests on the charger port floor.

3. When the battery cartridge is inserted, the charg-

ing light color will flash in red color and charging

will begin.

4. When charging is completed, the charging light

goes out. The charging time is as follows:

Battery 7000, 7100, 7120, 9000, 9100, 9100A,

9120: approx. 60 minutes.

5. If you leave the battery cartridge in the charger

after the charging cycle is complete, the charger

will switch into its ‘‘trickle charge (maintenance

charge)’’ mode.

6. After charging, remove the battery cartridge from

the charger and unplug the charger from the

power source.

Battery type

Capacity

(mAh)

Number of

cells

7000 1,300 6

9000 1,300 8

CAUTION:

•

The battery charger is for charging Makita battery

cartridge. Never use it for other purposes or for

other manufacturer’s batteries.

•

When you charge a new battery cartridge or a

battery cartridge which has not been used for a long

period of time, it may not accept a full charge. This

is a normal condition and does not indicate a

problem. You can recharge the battery cartridge

fully after discharging it completely and recharging a

couple of times.

•

When you charge a battery cartridge from a just-

operated machine or a battery cartridge which has

been left in a location exposed to direct sunlight or

heat for a long time, let it cool off. Then re-insert it

and try to charge it once more.

•

When you charge a new battery cartridge or a

battery cartridge which has not been used for a long

period, sometimes the charging light will go out

soon. If this occurs, remove the battery cartridge

and re-insert it. If the charging light goes out within

one minute even after repeating this procedure a

couple of times, the battery cartridge is dead.

Replace it with a new one.

DA301D/DA391D (Eng) (’100. 3. 15)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DA301D Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info