Bedienungsanleitung Makita DA301DB (Seite 6 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

600656

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

For DA301DB/DA391DB (Fig. 3)

Plug the battery charger into your power source.

Insert the battery cartridge so that the plus and minus

terminals on the battery cartridge are on the same

sides as their respective markings on the battery

charger. Insert the cartridge fully into the port so that

it rests on the charger port floor.

When the battery cartridge is inserted, the charging

light will come on and charging will begin. The charg-

ing light will keep lighting up steadily during charging.

When charging is completed, the charging light goes

out. The charging time is approx. 100 minutes. If you

leave the battery cartridge in the charger after the

charging cycle is complete, the charger will switch into

its ‘‘trickle charge (maintenance charge)’’ mode which

will last approximately 24 hours.

After charging, unplug the charger from the power

source.

Battery type

Capacity

(mAh)

Number of

cells

7033 2,200 6

9033 2,200 8

CAUTION:

•

If you charge a battery cartridge from a just-

operated machine or a battery cartridge which has

been left in a location exposed to direct sunlight for

a long time, the charging light may flash in red color.

If this occurs, wait for a while. Charging will begin

after the battery cartridge cools.

•

Any of the following conditions indicates damage to

the charger and/or battery cartridge. Ask your

Makita Authorized or Factory Service Center to

check them.

1) The charging light does not light up or flash (red)

when the battery is inserted in the charger port.

2) Charging is not completed at even more than

three hours after red light comes ON at start of

charging.

Trickle charge (Maintenance charge)

If you leave the battery cartridge in the charger to

prevent spontaneous discharging after full charge,

the charger will switch into its ‘‘trickle charge (main-

tenance charge)’’ mode and keep the battery car-

tridge fresh and fully charged.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop machine operation and charge the

battery cartridge when you notice less machine

power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tempera-

ture at 10°C – 40°C (50°F – 104°F).

Let a hot battery cartridge cool down before

charging it.

Installing or removing drill bit or driver bit

Important:

Always be sure that the machine is switched off and

the battery cartridge is removed before installing or

removing the bit.

For DA301D/DA301DB (Fig.4&6)

To install the bit, place it in the chuck as far as it will

go. Tighten the chuck by hand. Place the chuck key in

each of the three holes and tighten clockwise. Be sure

to tighten all three chuck holes evenly. To remove the

bit, turn the chuck key counterclockwise in just one

hole, then loosen the chuck by hand.

After use, return the chuck key to the storage cavity

on the machine.

For DA391D/DA391DB (Fig. 5)

Hold the ring and turn the sleeve counterclockwise to

open the chuck jaws. Place the bit in the chuck as far

as it will go. Hold the ring firmly and turn the sleeve

clockwise to tighten the chuck. To remove the bit, hold

the ring and turn the sleeve counterclockwise.

Switch action

(Fig. 7 for DA301D/DA301DB & Fig. 8 for

DA391D/DA391DB)

CAUTION:

•

Before inserting the battery cartridge into the

machine, always check to see that the switch trigger

actuates properly and returns to the ‘‘OFF’’ position

when released.

•

Always check the direction of rotation before opera-

tion.

•

Use the reversing switch lever only after the

machine comes to a complete stop. Changing the

direction of rotation before the machine stops may

damage the machine.

•

When not operating the machine, keep the revers-

ing switch lever in the neutral position.

Set the reversing switch lever just in front of the switch

trigger to

/ ‘‘FWD’’ side for clockwise rotation or

/ ‘‘REV’’ side for counterclockwise rotation. To

start the machine, simply pull the trigger. Machine

speed is increased by increasing pressure on the

trigger. Release the trigger to stop. When the revers-

ing switch lever is in the neutral position, the machine

will not start even if you pull the trigger.

Drilling operation

•

Drilling in wood

When drilling in wood, best results are obtained with

wood drills equipped with a guide screw. The guide

screw makes drilling easier by pulling the bit into the

workpiece.

•

Drilling in metal

To prevent the bit from slipping when starting a hole,

make an indentation with a center punch and ham-

mer at the point to be drilled. Place the point of the

bit in the indentation and start drilling.

Use a cutting lubricant when drilling metals. The

exceptions are iron and brass which should be

drilled dry.

DA301D/DA391D (Eng) (’100. 3. 8)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DA301DB Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info