Bedienungsanleitung Makita DA4000LR (Seite 5 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448288

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

ENGLISH

Explanation of general view

1 High

2 Low

3 Chuck key

4 Drill chuck

5Hex wrench

6 Loosen

7 Angle housing

8 Joint

9Socket

10 Bolt

11 HIGH

12 LOW

13 High speed operation

14 Two faces

15 Spindle

16 Tighten

17 Switch trigger

18 Reversing switch lever

19 Limit mark

20 Brush holder cap

21 Screwdriver

SPECIFICATIONS

Model DA4000LR

Drilling capacities

Steel ................................................................... 13 mm

Wood .................................................................. 38 mm

No load speed (min

-1

)

High ...................................................................0 – 900

Low .................................................................... 0 – 400

Overall length ...................................................... 413 mm

Net weight............................................................... 3.7 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

ADDITIONAL SAFETY RULES

ENB001-1

1. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tools

may contact hidden wiring or its own cord. Con-

tact with a ‘‘live’’ wire will make exposed metal

parts of the tool ‘‘live’’ and shock the operator.

2. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

3. Hold the tool firmly.

4. Keep hands away from rotating parts.

5. Do not leave the tool running. Operate the tool

only when hand-held.

6. Do not touch the drill bit or the workpiece imme-

diately after operation; they may be extremely

hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing angle attachment

CAUTION:

Always be sure that the tool is switched off and

unplugged before installing or removing the angle attach-

ment.

The angle head has a spindle on each end. For higher

speed operation, attach the drill chuck to the end marked

“HIGH”. The higher speed is better suited for drilling

smaller diameter holes. For lower speed operation,

attach the drill chuck to the end marked “LOW”. The

lower speed is best utilized for drilling larger diameter

holes. (Fig. 1)

The tool is factory assembled with the chuck on spindle

end marked “HIGH”.

To change to the “LOW” speed, proceed as follows:

To remove the drill chuck, first open the chuck jaws com-

pletely and place the chuck key in one of the key holes.

(Fig. 2)

Remove the chuck remaining bolt through the chuck

opening by turning it counterclockwise with the hex

wrench. (Fig. 3)

CAUTION:

The drill chuck and the bolt are assembled each other.

Turn the bolt counterclockwise about 10 times so that

they can be removed together.

Loosen the bolts of the joint by the hex wrench and

remove the angle housing, the joint and the socket.

(Fig. 4)

To install the socket and the joint, fit the socket to the

spindle so that the two faces are fitted perfectly. Then

install the joint. For higher speed operation, fit the angle

housing marked “LOW” to the joint.

For lower speed operation, fit the angle housing marked

“HIGH” to the joint. (Fig. 5)

Rotate the angle housing to the desired position. Tighten

the bolt with the hex wrench firmly. And retighten the

another bolt firmly again. (Fig. 6)

CAUTION:

Be sure to tighten the two bolts firmly, or it may present a

risk of injury to persons.

Slide the drill chuck to the spindle so that the two faces

are fitted perfectly. Holding the drill chuck with the chuck

key, tighten the bolt (for installing the drill chuck) clock-

wise with the hex wrench firmly. (Fig. 7 & 8)

The tool may be converted to a conventional straight

drive drill by installing the drill chuck without the angle

attachment. (Fig. 9)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DA4000LR Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita DA4000LR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info