Bedienungsanleitung Makita DBN500 (Seite 6 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600591

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

2. Do not point the tool towards yourself or anyone

nearby. Unexpected triggering will discharge the

fastener causing an injury.

3. Do not actuate the tool unless the tool is placed

firmly against the workpiece. If the tool is not in

contact with the workpiece, the fastener may be

deflected away from your target.

4. Disconnect the tool from the power source when

the fastener jams in the tool. While removing a

jammed fastener, the nailer may be accidentally

activated if it is plugged in.

5. Use caution while removing a jammed fastener.

The mechanism may be under compression and the

fastener may be forcefully discharged while

attempting to free a jammed condition.

6. Do not use this nailer for fastening electrical

cables. It is not designed for electric cable installation

and may damage the insulation of electric cables

thereby causing electric shock or fire hazards.

7. Always wear safety goggles or safety glasses with

side shield, and a full face shield when needed.

8. Keep hands and feet away from the ejection port

area.

9. Follow instruction for lubricating and changing

accessories.

10. Always remove the battery cartridge before

loading the fasteners, adjustment, inspection,

maintenance or after operation is over.

11. Make sure no one is nearby before operation.

Never attempt to drive fasteners from both the

inside and outside of wall at the same time.

Fasteners may rip through and/or fly off,

presenting a grave danger.

12. Watch your footing and maintain your balance

with the tool. Make sure there is no one below

when working in high locations.

13. Never use fastener driving tools marked with the

symbol “Do not use on scaffoldings, ladders” for

specific application for example:

- when changing one driving location to another

involves the use of scaffoldings, stairs, ladders, or

ladder alike constructions, e.g. roof laths;

- closing boxes or crates;

- fitting transportation safety systems e.g. on

vehicles and wagons.

14. Check walls, ceilings, floors, roofing and the like

carefully to avoid possible electrical shock, gas

leakage, explosions, etc. caused by stapling into

live wires, conduits or gas pipes.

15. Use only fasteners specified in this manual. The

use of any other fasteners may cause malfunction

of the tool.

16. Do not tamper with the tool or attempt to use it for

other than driving fasteners.

17. Do not operate the tool without fasteners. It

shortens the service life of the tool.

18. Stop driving operations immediately if you notice

something wrong or out of the ordinary with the

tool.

19. Never drive fastener into any materials which may

allow the fastener to puncture and fly through as a

projectile.

20. Never actuate the switch trigger and safety lever

at the same time until you are prepared to fastener

workpieces. Allow the workpiece to depress the

safety lever. Never defeat its purpose by securing

the safety lever back or by depressing it by hand.

21. Never tamper with the safety lever. Check the

safety lever frequently for proper operations.

22. Always remove fasteners from the tool when not

in use.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to safety

rules for the subject product. MISUSE or failure to

follow the safety rules stated in this instruction

manual may cause serious personal injury.

IMPORTANT SAFETY

INSTRUCTIONS ENC007-8

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all

instructions and cautionary markings on (1)

battery charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk

of overheating, possible burns and even an

explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it is

severely damaged or is completely worn out. The

battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10. Follow your local regulations relating to disposal

of battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the battery

cartridge when you notice less tool power.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DBN500 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info