Bedienungsanleitung Makita DCS232T (Seite 21 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

600554

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Service, spare parts and guarantee

Maintenance and repair

The maintenance and repair of modern engines as well as all safety devices require

qualified technical training and a special workshop equipped with special tools and

testing devices.

We therefore recommend that you consult a MAKITA service centre for all work not

described in this instruction manual.

The MAKITA service centres have all the necessary equipment and skilled and expe-

rienced personnel, who can work out cost-effective solutions and advise you in all

matters.

Please contact your nearest service centre.

Spare parts

Reliable long-term operation, as well as the safety of your chain saw, depend among

other things on the quality of the spare parts used. Use only original MAKITA parts.

Only original spare parts and accessories guarantee the highest quality in material,

dimensions, functioning and safety.

Original spare parts and accessories can be obtained from your local dealer. He will

also have the spare part lists to determine the required spare part numbers, and will

be constantly informed about the latest improvements and spare part innovations.

Please bear in mind that if parts other than original MAKITA spare parts are used, this

will automatically invalidate the MAKITA product guarantee.

Guarantee

MAKITA guarantees the highest quality and will therefore reimburse all costs for

repair by replacement of damaged parts resulting from material or production faults

occurring within the guarantee period after purchase. Please note that in some coun-

tries particular guarantee conditions may exist. If you have any questions, please con-

tact your salesman, who is responsible for the guarantee of the product.

Please note that we cannot accept any responsibility for damage caused by:

• Disregard of the instruction manual.

• Non-performance of the required maintenance and cleaning.

• Incorrect carburetor adjustment.

• Normal wear and tear.

• Obvious overloading due to permanent exceeding of the upper performance limits.

• Use of guide bars and chains which have not been approved.

• Use of guide bar and chain lengths which have not been approved.

• Use of force, improper use, misuse or accidents.

• Damage from overheating due to dirt on the recoil starter.

• Work on the chain saw by unskilled persons or inappropriate repairs.

• Use of unsuitable spare parts or parts which are not original MAKITA parts, insofar

as they have caused the damage.

• Use of unsuitable or old oil.

• Damage related to conditions arising from lease or rent contracts.

Cleaning, servicing and adjustment work is not covered by the guarantee. All repairs

covered by the guarantee must be performed by a MAKITA service centre.

Trouble shooting

Malfunction System Observation Cause

Chain does not run Chain brake Engine runs Chain brake actuated.

Engine does not start or

only with difficulty

Ignition system Ignition spark Malfunction in fuel supply system, compression system, mechanical malfunction.

No ignition spark Switch on STOP, fault or short-circuit in the wiring, plug cap or spark plug defective.

Fuel supply Fuel tank is filled Choke in wrong position, carburetor defective, suction head dirty, fuel line bent or

interrupted.

Compression system Inside Faulty crankcase gasket, radial shaft packings defective, cylinder or piston rings

defective.

Outside Spark plug does not seal.

Mechanical malfunction Starter does not engage Spring in starter broken, broken parts inside the engine.

Warm start difficulties Carburetor Fuel tank is filled

Ignition spark

Wrong carburetor adjustment.

Engine starts, but dies

immediately

Fuel supply Fuel tank is filled Wrong idling adjustment, suction head or carburetor dirty. Tank venting defective,

fuel line interrupted, cable defective, STOP switch defective.

Insufficient power Several systems may be

involved simultaneously

Engine is idling Air filter dirty, wrong carburetor adjustment, muffler clogged, exhaust channel in cyl-

inder clogged.

No chain lubrication Oil tank/pump No oil on the chain Oil tank empty.

Oil guide groove dirty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DCS232T Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info