Bedienungsanleitung Makita DCS460 (Seite 18 von 36) (Holländisch)

448334

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

HS L

CAUTION:

Do not adjust the carburetor until the machine has been

completely assembled and checked! Do not adjust the

carburetor without a tachometer!

Carburetor adjustment is necessary for optimum engine

performance, for safer and more economical operation.

Adjust the carburetor only with the engine warm, a clean

air Þ lter, and properly installed cutting tool.

Carburetor adjustment may be done only by a MAKITA

service centre. Improper adjustment can cause damage

to the engine.

In order to comply with new emissions legislation, limits have

been placed on the carburetor adjusting screws (H) and (L).

This limitation (to about 180 degrees) prevents an exces-

sively rich mixture. This in turn ensures compliance with

emissions rules as well as optimum engine performance and

economical fuel consumption.

You will need a tachometer (part No. 950 233 210) for op-

timum adjustment. Exceeding the maximum permissible

speed can lead to overheating and under-lubricating, and

damage to the engine!

Factory setting of adjusting screws (H) and (L): Turned out

almost all the way (counterclockwise).

Use a screwdriver (blade width 4 mm, part No. 944 340 001)

to adjust the screws.

For proper adjustment, proceed as follows:

Checking adjusting screw (H)

Before starting the engine make sure that adjusting screw (H) is

turned out counterclockwise until it reaches a noticeable stop.

The limitations do not prevent excessively lean running!

1. Start engine and let it warm up (3-5 minutes)

2. Set idle

3. Check acceleration

4. Set maximum permissible speed

5. Check idle speed

2. Set idle

Set the idle speed per the technical speciÞ cations.

Turning the adjusting screw (S) in (clockwise) increases the

idle speed. Turning it out (counter-clockwise) lowers the idle

speed. The cutting tool must not rotate!

3. Check acceleration

When the throttle is pressed, the engine should go smoothly

from idle to high speed.

Turn adjusting screw (L) out (counterclockwise) in small

increments until acceleration is good.

4. Set maximum permissible speed

Set the maximum speed by minimal adjustments of

the adjusting screw (H) in accordance with the tech-

nical speciÞ cations. Turning the adjusting screw (H)

clockwise increases the speed. Never exceed the

maximum permissible speed!

For units with electronic engine speed limitation:

No tachometer is necessary to determine the

maximum permissible speed, since exceeding

this speed will result in clearly audible ignition

misses!

5. Check idle speed

Check the idle speed after setting the top speed (the

cutting tool must not rotate!).

Repeat the adjustment procedure starting at Step 2,

until the engine runs with the correct idle speed, good

acceleration, and maximum permissible speed.

Adjusting the carburetor (only for EU-countries)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DCS460 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita DCS460

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info