Bedienungsanleitung Makita DDA460 (Seite 8 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691085

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

8 ENGLISH

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

►Fig.5: 1. Lamp

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

Thelampgoesoutapproximately10secondsafter

releasing the switch trigger.

NOTE:

When the tool is overheated, the tool stops

automaticallyandthelampstartsashing.Inthiscase,

release the switch trigger. The lamp turns off in 5 minute.

NOTE:Useadryclothtowipethedirtoffthelensof

the lamp. Be careful not to scratch the lens of lamp, or

itmaylowertheillumination.

Reversing switch action

►Fig.6: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION:

Use the reversing switch only after

the tool comes to a complete stop. Changing the direc-

tionofrotationbeforethetoolstopsmaydamagethetool.

CAUTION:

When not operating the tool, always

set the reversing switch lever to the neutral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the

A side for clockwise rotation or from the B side for coun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion, the switch lever cannot be pulled.

Automatic speed change function

This tool has "high speed mode" and "high torque mode".

Thetoolautomaticallychangestheoperationmode

depending on the work load. When the work load is low,

the tool will run in the "high speed mode" for quicker

operation. When the work load is high, the tool will run

in the "high torque mode" for powerful operation.

►Fig.7: 1. Mode indicator

The mode indicator lights up in green when the tool is

running in "high torque mode".

If the tool is operated with excessive load, the mode indicator

will blink in green. The mode indicator stops blinking and

thenlightsuporturnsoffifyoureducetheloadonthetool.

Mode indicator status Operation

mode

On Off Blinking

High speed

mode

High torque

mode

Overload

alert

Speed change

NOTICE: Use the speed change knob only after

the tool comes to a complete stop. Changing the

toolspeedbeforethetoolstopsmaydamagethetool.

NOTICE: Always set the speed change knob

carefully into the correct position.Ifyouoperate

the tool with the speed change knob positioned half-

waybetweentheposition1andtheposition2,the

toolmaybedamaged.

Two speed ranges can be preselected with the speed

change knob.

To change the speed, depress the lock button and turn

the speed change knob so that the pointer points to the

position 1 for low speed or the position 2 for high speed.

►Fig.8: 1. Lock button 2. Pointer 3. Speed change

knob

Torque limiter

The torque limiter will actuate when a certain torque

levelisreachedatthelowspeedsetting(position1).

The motor will disengage from the output shaft. When

this happens, the drill bit will stop turning.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing side grip (auxiliary handle)

CAUTION: Always be sure that the side grip is

installed securely before operation.

Screwthesidegriponthetoolsecurely.Thesidegrip

can be installed on either side of the tool, whichever is

convenient.

►Fig.9: 1. Side grip

Front handle

CAUTION: Do not x the front handle beyond

the limits of the arrow as illustrated. Be cautious

that your hand is not caught in the grip. Keep the

hand away from the drill chuck.Theycanleadto

serious accidents.

CAUTION: Always be sure that the hex bolts

(both sides) of the front handle are tightened

securely.

Thefronthandlecanbeinstalledinanypositionwithin

0° - 112.5° as illustrated.

►Fig.10: 1. Front handle

Tochangetheposition,loosenthehexbolts(both

sides)withahexwrenchandturnthefronthandletothe

desiredposition.Thentightenthehexboltssecurely.

►Fig.11: 1. Front handle 2. Hex wrench

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DDA460 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info