Bedienungsanleitung Makita DDF470 (Seite 6 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600533

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

013980

NOTE:

• The LED display goes off approximately one minute

after releasing the switch trigger to save the battery

power. To check the remaining battery capacity,

slightly pull the switch trigger.

• When the LED display lights up but the tool does not

work even with a recharged battery cartridge, cool

down the tool fully. If the condition does not change,

have the tool repaired by a Makita local service center.

Switch action (Fig. 4)

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

Lighting up the front lamp (Fig. 5)

CAUTION:

• Do not look in the light or see the source of light

directly.

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

The lamp goes out 10 -15 seconds after releasing the

trigger.

NOTE:

• When the tool is overheated, the tool stops

automatically and the lamp starts flashing. In this case,

release the switch trigger. The lamp turns off in one

minute.

• Use a dry cloth to wipe the dirt off the lens of the lamp.

Be careful not to scratch the lens of lamp, or it may

lower the illumination.

Reversing switch action (Fig. 6)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position.

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for

counterclockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

Speed change (Fig. 7)

CAUTION:

• Always set the speed change lever fully to the correct

position. If you operate the tool with the speed change

lever positioned halfway between the “1” side and “2”

side, the tool may be damaged.

• Do not use the speed change lever while the tool is

running. The tool may be damaged.

• If the tool speed is coming down extremely during the

operation with “2”, slide the lever to the “1” and restart

the operation.

013983

To change the speed, switch off the tool first. Select the

“2” side for high speed or “1” for low speed but high

torque. Be sure that the speed change lever is set to the

correct position before operation.

Adjusting the fastening torque (Fig. 8)

The fastening torque can be adjusted in 17 steps by

turning the adjusting ring. Align the graduations with the

arrow on the tool body. You can get the minimum

fastening torque at 1 and maximum torque at marking.

The clutch will slip at various torque levels when set at the

number 1 to 16. The clutch does not work at the

marking.

Before actual operation, drive a trial screw into your

material or a piece of duplicate material to determine

which torque level is required for a particular application.

The following shows the rough guide of the relationship

between the screw size and graduation.

LED indicator status Remaining battery capacity

About 50% or more

About 20% - 50%

About less than 20%

Position of

speed adjusting

lever

Speed Torque

Applicable

operation

1 Low High

Heavy loading

operation

2 High Low

Light loading

operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DDF470 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info