Bedienungsanleitung Makita DDF481 (Seite 6 von 14) (Englisch, Holländisch)

600532

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

013980

NOTE:

• The LED display goes off approximately one minute

after releasing the switch trigger to save the battery

power. To check the remaining battery capacity,

slightly pull the switch trigger.

• When the LED display lights up but the tool does not

work even with a recharged battery cartridge, cool

down the tool fully. If the condition does not change,

have the tool repaired by a Makita local service center.

Switch action

CAUTION:

• Before installing the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released. (Fig. 4)

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

Lighting up the front lamp

CAUTION:

• Do not look in the light or see the source of light

directly. (Fig. 5)

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

The lamp goes out 10 -15 seconds after releasing the

trigger.

NOTE:

• When the tool is overheated, the tool stops

automatically and the lamp starts flashing. In this case,

release the switch trigger. The lamp turns off in one

minute.

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

Reversing switch action

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position. (Fig. 6)

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for

counterclockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

Speed change

CAUTION:

• Always set the speed change lever fully to the correct

position. If you operate the tool with the speed change

lever positioned halfway between the “1” side and, “2”

side, the tool may be damaged.

• Do not use the speed change lever while the tool is

running. The tool may be damaged. (Fig. 7)

To change the speed, first switch off the tool and then

slide the speed change lever to the “2” side for high speed

or, “1” side for low speed. Be sure that the speed change

lever is set to the correct position before operation. Use

the right speed for your job.

Selecting the action mode

CAUTION:

• Always set the ring correctly to your desired mode

mark. If you operate the tool with the ring positioned

halfway between the mode marks, the tool may be

damaged. (Fig. 8)

This tool has an action mode changing ring. For drilling,

turn the ring so that the arrow on the tool body points

toward the mark on the ring. For screwing, turn the ring

so that the arrow points toward the mark on the ring.

Adjusting the fastening torque

(screwdriver mode “ ”) (Fig. 9)

The fastening torque can be adjusted in 21 steps by

turning the adjusting ring so that its graduations are

aligned with the pointer on the tool body.

First, slide the action mode change lever to the position of

symbol.

The fastening torque is minimum when the number 1 is

aligned with the pointer, and maximum when the marking

is aligned with the pointer. The clutch will slip at various

torque levels when set at the number 1 to 21. Before

actual operation, drive a trial screw into your material or a

piece of duplicate material to determine which torque level

is required for a particular application.

NOTE:

• The adjusting ring does not lock when the pointer is

positioned only halfway between the graduations.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing side grip (auxiliary handle)

(Fig. 10)

Always use the side grip to ensure operating safety.

Insert the side grip so that the groove on the arm fit in one

of the counter parts on the tool. Then tighten the grip by

turning clockwise.

LED indicator status Remaining battery capacity

About 50% or more

About 20% - 50%

About less than 20%

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DDF481 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita DDF481

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info