Bedienungsanleitung Makita DDF482RTJ (Seite 8 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711036

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

8 ENGLISH

Reversing switch action

►Fig.6: 1. Reversing switch lever

CAUTION: Always check the direction of rota-

tion before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

directionofrotationbeforethetoolstopsmaydam-

age the tool.

CAUTION: When not operating the tool, always

set the reversing switch lever to the neutral

position.

Thistoolhasareversingswitchtochangethedirection

of rotation. Depress the reversing switch lever from the

AsideforclockwiserotationorfromtheBsideforcoun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion,theswitchtriggercannotbepulled.

Speed change

►Fig.7: 1. Speed change lever

CAUTION: Always set the speed change lever

fully to the correct position. If you operate the

tool with the speed change lever positioned halfway

betweenthe"1"sideand"2"side,thetoolmaybe

damaged.

CAUTION: Do not use the speed change lever

while the tool is running.Thetoolmaybedamaged.

Position of

speed

change lever

Speed Torque Applicable

operation

1 Low High Heavy load-

ing operation

2 High Low Light loading

operation

Tochangethespeed,switchoffthetoolrst.Select

the"2"sideforhighspeedor"1"forlowspeedbuthigh

torque.Besurethatthespeedchangeleverissettothe

correctpositionbeforeoperation.

If the tool speed is coming down extremely during the

operationwith"2",slidethelevertothe"1"andrestart

the operation.

Adjusting the fastening torque

►Fig.8: 1.Adjustingring  2.Graduation  3.Arrow

Thefasteningtorquecanbeadjustedin22stepsbyturningtheadjustingring.Alignthegraduationswiththearrow

onthetoolbody.Youcangettheminimumfasteningtorqueat1andmaximumtorqueat

marking.

Theclutchwillslipatvarioustorquelevelswhensetatthenumber1to21.Theclutchdoesnotworkatthe

marking.

Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which

torquelevelisrequiredforaparticularapplication.

Thefollowingshowstheroughguideoftherelationshipbetweenthescrewsizeandgraduation.

Graduation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Machine screw M4 M5 M6

Wood

screw

Soft wood

(e.g. pine)

– ɸ3.5 x 22 ɸ4.1x 38 –

Hard wood

(e.g. lauan)

– ɸ3.5 x 22 ɸ4.1x 38 –

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/

drill bit

►Fig.9: 1. Sleeve 2. Close 3. Open

Turnthesleevecounterclockwisetoopenthechuck

jaws.Placethedriverbit/drillbitinthechuckasfar

asitwillgo.Turnthesleeveclockwisetotightenthe

chuck.Toremovethedriverbit/drillbit,turnthesleeve

counterclockwise.

Installing hook

►Fig.10: 1. Groove 2. Hook 3. Screw

Thehookisconvenientfortemporarilyhangingthetool.

Thiscanbeinstalledoneithersideofthetool.Toinstall

the hook, insert it into a groove in the tool housing on

eithersideandthensecureitwithascrew.Toremove,

loosen the screw and then take it out.

Installing driver bit holder

Optional accessory

►Fig.11: 1.Driverbitholder  2.Driverbit

Fitthedriverbitholderintotheprotrusionatthetoolfoot

on either right or left side and secure it with a screw.

Whennotusingthedriverbit,keepitinthedriverbit

holders.Driverbits45mm-longcanbekeptthere.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DDF482RTJ Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info