Bedienungsanleitung Makita DES 400 (Seite 14 von 54) (Englisch, Holländisch, Französisch)

448348

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

To guarantee a troublefree operation of the oil pump the oil

guide groove (A/16) as well as the oil inlet bore in the guide bar

(A/17) must be cleaned in regular intervals.

- When switching on the electric chain saw always hold

it with both hands.

- Take the back handle with the right hand and the tubular

handle with the left hand. Hold the handles tightly with your

thumbs facing your fingers. The bar and chain must not be

in contact with any object.

- First depress the locking button (B/18) and then the power

switch (B/19). Then release the locking button (B/18).

- Attention: The chain starts running immediately. Keep

the power switch depressed as long as the motor is to run.

CAUTION:

Never lock the power switch in the ON position.

Switching off the motor:

- Release the power switch (B/19).

CAUTION:

The saw chain will continue to run for a short time. Do not

deposite the chain saw before the chain is at a standstill.

Note on Model DES 380:

The DES 380 electric saw is equipped with overload protec-

tion. In the event that the electric motor should overheat, the

thermal circuit breaker (B/20) will automatically pop out, inter-

rupting the flow of current.

After allowing the motor to cool down for about 30 seconds,

push the thermal circuit breaker back in to restore operation

of the saw. Always allow the unit to cool down for 30

seconds!

IMPOTANT NOTE: Turning on machines causes transient

voltage dips. If the conditions of the power supply network are

unfavourable, there might be interference with other devices

on the same network. If the impedance of the network is lower

than 0,093 Ohms it can pressumed that no interference will

happen.

Switching on the motor

Checking the chain brake

Do not work with the chain saw without first checking the

chain brake!

- Start the motor as described (make sure you have a good

footing, and place the chain saw on the ground in such a

way that the guide bar is free of contact).

- Grasp the tubular handle

firmly with one hand and hold the

grip with the other.

- Switch on the motor and press the hand guard (C/1) in the

direction of the arrow

with the back of your hand until the

chain brake engages. The chain should stop immediately.

- Switch the motor off

Immediately and release the chain

brake.

IMPORTANT: If the chain does not stop immediately when

you test the chain brake, do NOT use the chain saw. Take

the chain saw to a MAKITA service center.

Checking the chain lubrication

Never saw when a sufficient chain lubrication is not guaranteed.

Otherwise the life of the sawing device will be reduced. Before

starting work check the oil level in the tank and the oil feeding.

Check the fed oil quantity by following the instructions below:

- Start the electric chain saw.

- Hold the running chain saw approx. 15 cm above a trunk or

the ground (use an appropriate surface).

If the lubrication is sufficient, you will see a light oiltrace

because oil will be centrifuged from the chain saw.

Pay attention to the direction the wind is blowing and avoid

unnecessary exposure to the oil spray!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DES 400 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita DES 400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info