Bedienungsanleitung Makita df010dse (Seite 6 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

381603

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Guideline for clutch auto-stop

Lighting up the front lamp (Fig. 6 & 7)

CAUTION:

• Do not look in the light or see the source of light

directly.

To turn on the light, slide the lamp switch to the A position.

To turn off the light, slide the lamp switch to the B position.

Even if you leave the lamp on, the light will automatically

turn off after 5 minutes.

Checking the remaining battery capacity,

auto-stop

The lamp signals by flickering when the battery power is

almost used up during use.

At this time, recharge the battery or replace the battery

with a fully charged one.

ASSEMBLY

CAUTION:

• Always be sure that the lock button is in the locked

position B and the battery cartridge is removed before

carrying out any work on the tool.

Installing or removing driver bit or socket

bit (Fig. 8)

Use only the driver bit or socket bit shown in the figure.

Do not use any other driver bit or socket bit.

For European and North & South American countries,

Australia and New Zealand

For other countries

1. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will

go. Then release the sleeve to secure the bit. (Fig. 9)

2. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit-piece and bit into the sleeve

as far as it will go. The bit-piece should be inserted

into the sleeve with its pointed end facing in. Then

release the sleeve to secure the bit. (Fig. 10)

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out firmly.

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

OPERATION

The tool can be used in two ways; a straight type and a

pistol type which is selectable according to the conditions

of workplace and screwdriving. (Fig. 11)

Screwdriving operation (Fig. 12)

CAUTION:

• Adjust the adjusting ring to the proper torque level for

your work.

Place the point of the driver bit in the screw head and

apply pressure to the tool. Then switch the tool on. When

the clutch cuts in, the motor will stop automatically. Then

release the switch.

CAUTION:

• Make sure that the driver bit is inserted straight in the

screw head, or the screw and/or bit may be damaged.

NOTE:

• When driving wood screws, predrill pilot holes to make

driving easier and to prevent splitting of the workpiece.

See the chart.

Work range of

clutch auto-stop

Increments on

adjusting ring

for fastening

torque

Fastening torque

High

speed

Low

speed

Clutch auto-

stop works

Approx. 0.3 N·m

(Approx. 3 Kgf-cm)

Approx. 0.82 N·m

(Approx. 8.4 Kgf-cm)

Approx. 1.35 N·m

(Approx. 13.8 Kgf-cm)

Approx. 1.88 N·m

(Approx. 19.2 Kgf-cm)

Approx. 2.41 N·m

(Approx. 24.6 Kgf-cm)

Approx. 2.9 N·m

(Approx. 30 Kgf-cm)

Clutch auto-

stop does not

work

Low speed

Approx. 5 N·m

(Approx. 49 Kgf-cm)

High speed

Approx. 1.5 N·m

(Approx. 14.7 Kgf-cm)

When driving

machine

screws

Increments

Guideline for machine

screw diameter

1 - 3 2.5 mm

4 - 8 3 mm

9 - 18 4 mm

19 - 21 5 mm

A=12mm

B=9mm

Use only these type of bit. Follow the

procedure (1).

(Note) Bit-piece is not necessary.

A=17 mm

B=14 mm

To install these types of bits, follow the

procedure (1).

(Note) Makita bits are these types.

A=12 mm

B=9 mm

To install these types of bits, follow the

procedure (2).

(Note) Bit-piece is necessary for installing

the bit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita df010dse Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info