Bedienungsanleitung Makita DF031D (Seite 8 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600464

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

8 ENGLISH

Position of

speed

change lever

Speed Torque Applicable

operation

1 Low High Heavy load-

ing operation

2 High Low Light loading

operation

Tochangethespeed,switchoffthetoolrst.Select

the"2"sideforhighspeedor"1"forlowspeedbuthigh

torque.Besurethatthespeedchangeleverissettothe

correctpositionbeforeoperation.

If the tool speed is coming down extremely during the

operationwith"2",slidethelevertothe"1"andrestart

the operation.

Adjusting the fastening torque

[Fig.7: 1.Adjustingring  2.Graduation  3.Arrow]

Thefasteningtorquecanbeadjustedin19stepsbyturningtheadjustingring.Alignthegraduationswiththearrow

onthetoolbody.Youcangettheminimumfasteningtorqueat1andmaximumtorqueat

marking.

Theclutchwillslipatvarioustorquelevelswhensetatthenumber1to18.Theclutchdoesnotworkatthe

marking.

Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which

torquelevelisrequiredforaparticularapplication.

Thefollowingshowstheroughguideoftherelationshipbetweenthescrewsizeandgraduation.

Graduation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Machine screw M4 M5 M6

Wood

screw

Soft wood

(e.g. pine)

– ɸ3.5 x 22 ɸ4.1x 38

Hard wood

(e.g. lauan)

– ɸ3.5 x 22 –

– ɸ4.1x 38

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/drill

bit

For Model DF331D (optional accessory)

[Fig.8: 1. Sleeve 2. Close 3. Open]

Turnthesleevecounterclockwisetoopenthechuck

jaws.Placethedriverbit/drillbitinthechuckasfar

asitwillgo.Turnthesleeveclockwisetotightenthe

chuck.Toremovethedriverbit/drillbit,turnthesleeve

counterclockwise.

Installing or removing driver bit/

socket bit

For Model DF031D (optional accessory)

[Fig.9]

Useonlydriverbit/socketbitthathasinsertingportion

showninthegure.Donotuseanyotherdriverbit/

socketbit.

For tool with shallow driver bit hole

A=12mm

B=9mm

Use only these type of driver

bit.Followtheprocedure

1. (Note) Bit-piece is not

necessary.

For tool with deep driver bit hole

A=17mm

B=14mm

Toinstallthesetypesofdriver

bits,followtheprocedure1.

A=12mm

B=9mm

Toinstallthesetypesofdriver

bits,followtheprocedure2.

(Note) Bit-piece is necessary

forinstallingthebit.

1. Toinstallthedriverbit,pullthesleeveinthedirec-

tionofthearrowandinsertthedriverbitintothe

sleeve as far as it will go.

Thenreleasethesleevetosecurethedriverbit.

[Fig.10: 1.Driverbit  2.Sleeve]

2. Toinstallthedriverbit,pullthesleeveinthedirec-

tionofthearrowandinsertthebit-pieceanddriver

bitintothesleeveasfarasitwillgo.Thebit-piece

shouldbeinsertedintothesleevewithitspointed

endfacingin.Thenreleasethesleevetosecure

thedriverbit.

[Fig.11: 1.Driverbit  2.Bit-piece  3.Sleeve]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DF031D Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info