Bedienungsanleitung Makita DF332DSAJ (Seite 9 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711023

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

9 ENGLISH

Toremovethedriverbit,pullthesleeveinthedirection

ofthearrowandpullthedriverbitout.

NOTE:Ifthedriverbitisnotinserteddeepenough

intothesleeve,thesleevewillnotreturntoitsoriginal

positionandthedriverbitwillnotbesecured.Inthis

case,tryre-insertingthebitaccordingtotheinstruc-

tionsabove.

NOTE:Afterinsertingthedriverbit,makesurethatit

isrmlysecured.Ifitcomesout,donotuseit.

Installing hook

►Fig.12: 1. Groove 2. Hook 3. Screw

Thehookisconvenientfortemporarilyhangingthetool.

Thiscanbeinstalledoneithersideofthetool.Toinstall

thehook,insertitintoagrooveinthetoolhousingon

eithersideandthensecureitwithascrew.Toremove,

loosenthescrewandthentakeitout.

Installing driver bit holder

Optional accessory

►Fig.13: 1.Driverbitholder2.Driverbit

Fitthedriverbitholderintotheprotrusionatthetoolfoot

oneitherrightorleftsideandsecureitwithascrew.

Whennotusingthedriverbit,keepitinthedriverbit

holders.Driverbits45mm-longcanbekeptthere.

OPERATION

CAUTION: Always insert the battery cartridge

all the way until it locks in place.Ifyoucansee

theredpartontheuppersideofthebutton,itisnot

lockedcompletely.Insertitfullyuntiltheredpartcan-

notbeseen.Ifnot,itmayaccidentallyfalloutofthe

tool,causinginjurytoyouorsomeonearoundyou.

CAUTION: When the speed comes down

extremely, reduce the load or stop the tool to

avoid the tool damage.

Holdthetoolrmlywithonehandonthegripandthe

otherhandonthebottomofthebatterycartridgeto

control the twisting action.

►Fig.14

Screwdriving operation

CAUTION: Adjust the adjusting ring to the

proper torque level for your work.

CAUTION: Make sure that the driver bit is

inserted straight in the screw head, or the screw

and/or driver bit may be damaged.

Placethepointofthedriverbitinthescrewheadand

applypressuretothetool.Startthetoolslowlyandthen

increasethespeedgradually.Releasetheswitchtrigger

assoonastheclutchcutsin.

NOTE: When driving wood screw, pre-drill a pilot hole

2/3thediameterofthescrew.Itmakesdrivingeasier

andpreventssplittingoftheworkpiece.

Drilling operation

First,turntheadjustingringsothatthepointerpointsto

the marking.Thenproceedasfollows.

Drilling in wood

Whendrillinginwood,thebestresultsareobtained

withwooddrillsequippedwithaguidescrew.Theguide

screwmakesdrillingeasierbypullingthedrillbitinto

the workpiece.

Drilling in metal

Topreventthedrillbitfromslippingwhenstartinga

hole,makeanindentationwithacenter-punchand

hammeratthepointtobedrilled.Placethepointofthe

drillbitintheindentationandstartdrilling.

Useacuttinglubricantwhendrillingmetals.Theexcep-

tionsareironandbrasswhichshouldbedrilleddry.

CAUTION: Pressing excessively on the tool

will not speed up the drilling.Infact,thisexcessive

pressurewillonlyservetodamagethetipofyourdrill

bit,decreasethetoolperformanceandshortenthe

servicelifeofthetool.

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece.Thereisatremendousforceexertedon

thetool/drillbitatthetimeofholebreakthrough.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure small workpieces

in a vise or similar hold-down device.

CAUTION: If the tool is operated continuously

until the battery cartridge has discharged, allow

the tool to rest for 15 minutes before proceeding

with a fresh battery.

Using the tool as a hand screwdriver

►Fig.15

Switchoffthetool.

Movethereversingswitchlevertotheneutralposition.

Turntheadjustingringsothatthearrowpointsto

the

marking.

Turnthetool.

NOTE:Thisuseisconvenientforcheckingthe

screwdriving.

NOTE:Donotusethetoolforworkrequiringexces-

siveforce,suchastighteningboltorremovingrusted

screws.

Makita DF332DSAJ Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info