Bedienungsanleitung Makita DFR750 (Seite 8 von 48) (Deutsch, Polnisch)

600458

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

OPERATION

Driving operation

Fig.15

Switch on the tool by pulling the switch trigger. Hold the

tool squarely and firmly up against the driving surface. A

screw will be automatically carried to the driving position

and fastened.

CAUTION:

• Always check the bit carefully for wear before

driving operations. Replace a worn bit or poor

fastening may result.

• Always hold the tool squarely against the driving

surface. Holding it at an angle may damage the

screw heads and cause wear on the bit. This may

also lead to poor fastening.

• Always keep the tool firmly against the driving

surface until the driving is over. Failure to do so

may cause insufficient fastening of screws.

• Be careful not to drive a screw onto another screw

already fastened.

• Do not operate the tool without screws. It will

damage the driving surface.

• Do not apply oil or grease on the sliding surface of

the feeder box.

Driving in corner

Fig.16

This tool can be used to drive at a position 15 mm away

from the wall as shown in the figure.

CAUTION:

• Driving at a position closer than 15 mm to the wall

or driving with the stopper base in contact with the

wall may damage the screw heads and cause wear

on the bit. This may also lead to poor fastening of

screws and malfunction of the tool.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may

result.

Replacing carbon brushes

Fig.17

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Loosen the thumb screws which secure the casing. Pull

out the casing in the direction of the arrow.

Fig.18

Use a screwdriver to remove two screws then remove

the front cover.

Fig.19

Raise the arm part of the spring and then place it in the

recessed part of the housing with a slotted bit

screwdriver of slender shaft or the like.

Fig.20

Use pliers to remove the carbon brush caps of the carbon

brushes. Take out the worn carbon brushes, insert the

new ones and replace the carbon brush caps in reverse.

Fig.21

Make sure that the carbon brush caps have fit into the

holes in brush holders securely.

Fig.22

Reinstall the front cover and tighten two screws securely.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are

recommended for use with your Makita tool

specified in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or

attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Drywall screw strip

• Phillips bit

• Various type of Makita genuine batteries and

chargers

• Plastic carrying case

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DFR750 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita DFR750

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info