Bedienungsanleitung Makita DFT022F (Seite 6 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691710

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Lighting up the lamps (Fig. 5)

CAUTION:

• Do not look in the light or see the source of light

directly.

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

The light automatically goes out 10 seconds after the

switch trigger is released.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

LED indicator (Fig. 6)

The LED indicator on the tool shows the following functions.

013073

Function Status

Status of the LED indicator/beeper

Action to be

taken

LED indicator Beeper

Auto-stop fastening

This function works when the tool has

reached the preset fastening torque

and normal tightening has been

completed. This helps overtightening

to be avoided.

Lights up in

green for

approximately

one second.

——

Delayed re-start

For approximately one second after

auto-stop fastening, the tool does not

start even if the switch trigger is

pulled.

Warning against

insufficient fastening

Insufficient fastening has been

performed when the switch trigger

has released before reaching the

preset fastening torque.

Lights up in red. A long beep

Retighten the

screw.

Warning for battery

cartridge capacity

This indicates the appropriate time to

replace the battery cartridge when

the battery power becomes low.

Flickers in red

slowly.

A series of long

beeps

Replace the

battery with fully

charged one.

Checking the

remaining battery

capacity, Autostop

This function works when the battery

power is almost used up. At this time,

tool stops immediately.

Lights up in red. A long beep

Replace the

battery with fully

charged one.

Check the LED

indicator, lamp and

beeper operation

This function works to check the

proper operation of the LED indicator,

lamp and beeper when a battery

cartridge has been inserted into the

tool.

Lights up first in

green, next red.

(And then the

lamp comes

on.)

A series of very

short beeps

—

Anti-reset of

controller

This function works when an

abnormal drop of the battery voltage

occurs for some reason, and the tool

stops.

Flickers in red

and green

alternatively.

A series of short

beeps

Replace the

battery with fully

charged one.

Overheat

This function works when the

temperature of the controller goes up

very highly, and the tool stops.

Flickers in red

quickly.

A series of short

beeps

Remove the

battery cartridge

immediately and

cool the tool

down.

Operation error of

the switch trigger

This function works to avoid the tool’s

immediate start upon insertion of

battery cartridge into the tool with the

switch trigger being pulled.

Flickers in red

and green

alternatively.

A series of short

beeps

Release the

switch trigger.

Warning for limit of

the fastening

capacity

The tool automatically stops without

the clutch working when exceeding

the fastening capacity limit.

Flick

ers in red

and green

alternatively.

A series of short

beeps

Remove the

battery cartridge

and then install

it again.

Be sure to use

the tool under

load within its

capacity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DFT022F Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info