Bedienungsanleitung Makita DFT041R (Seite 7 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

600448

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

011058

Note: These values can be changed on PC (except for DFT041R). Refer to SRCV02 USER MANUAL for details.

For LED#B (Fig. 6)

Led indicator / Beeper on the tool shows the following functions.

007929

Note 1: Refer to a instruction manual of receiver (acces-

sory) RCV02 when connecting it.

Note 2: Communication distance: 10 m or less (variable

up to 10 m depending on the operation environment)

CAUTION:

• Make sure that LED#B (2) does not light up before

removing a battery cartridge from the tool. If a battery

cartridge is removed while LED#B (2) lights up or

blinks, tools stored data will be deleted.

Adjusting the fastening torque (Fig. 7 & 8)

When you wish to drive machine screws, wood screws,

hex bolts, etc. with the predetermined torque, adjusting

the fastening torque as follows.

1. First remove the battery cartridge from the tool.

2. Loosen and remove the screw that secures ring.

3. Rotate the ring in the front of the tool by hand so that a

hole can be seen below the ring.

Status of

the LED indicator/beeper

Function Status Action to be taken

LED indicator Beeper

Blinks in red

and yellow

alternatively.

A long beep

Warning against

insufficient

fastening

Fastening is incomplete when switch

trigger of tool is released before clutch

activation.

Double-hitting

detection

This function works when a screw is

refastened after fastening.

Angle judge NOK

This function works when a screw is not

fastened within the angle range preset

on PC (Note).

Rundown NOK

This function works when a fastening is

finished before it reaches the preset

angle range. (Note)

Torque impossible

monitoring

This function works when torque

monitoring is cannot be carried out.

Blinks in red

and blue

alternatively.

A series of

short beeps

Disconnection

(when using

receiver RCV02)

Radio communication not yet

established

Finish necessary

connection or remove

a battery cartridge to

escape.

Radio

communication

failure

This function works when there is radio

communication failure.

Take it to a Makita

Authorized Service

centers.

Description Viewed color View and status

LED#B (1) Green

1 lights up when the tool is connected to a receiver.

2blinks

when the tool is on the step of being connected to a

receiver. (Note 1)

3 is turned off

one of the status below

3-1 when the battery cartridge is removed from the tool.

3-2

when the tool is left idle for more than 15 minutes

with a installed battery cartridge.

3-3

when the tool is not within the transmission dis-

tance. (Note 2)

LED#B (2) Red

1 lights up

when the tool’s stored number of data reaches its storable

number of data.

2blinks

when the tool’s stored number of data is equal to or smaller

than its storable number of data.

3 is turned off when the tool has no stored data to transmit to a receiver.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DFT041R Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info