Bedienungsanleitung Makita DFT060T (Seite 9 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

793613

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

9ENGLISH

LED indicator / Beeper

The LED indicators and beeper become activated when the tool works in the following operating conditions and

notify you of the tool status and performance currently delivered on the control panel.

Fig.7: 1. LED indicator A (in green, red, blue and yellow colors) 2. LED indicator B (in blue color) (* Not serve as

indicator for this model) 3. Error code 4. Status symbol

Error code

and status

symbol on

screen

Tool performance

and function

Tool status LED indicators/beeper status Action to be taken

LED indicators Beeper

-Operation check for

indicators and beeper

The tool starts to verify indica-

tors and beeper operation soon

after the battery cartridge is

installed.

The LED indicator



in green, red and

blue in order, and

then the front

lamp lights up.

A series of

very short

beeps

E00 Accidental start

prevention

The tool automatically stops

to avoid unintentional start-up

when the battery cartridge is

installed with the switch trigger

pulled.

The LED indicator



green alternately.

A series

of short

beeps

Release the switch

trigger.

E01 Auto-stop The battery power becomes

low and it is time to replace the

battery cartridge.

The LED indicator



green alternately.

A series

of short

beeps

Replace the battery

with fully charged

one.

E02 Anti-reset of controller The battery voltage drops

abnormally for some reason,

and the tool automatically stops

operation.

The LED indicator



green alternately.

A series

of short

beeps

Replace the battery

with fully charged

one.

E03 Auto-stop for low

remaining battery

power

The battery power is almost

used up, and the tool automati-

cally stops operation.

The LED indicator

lights up in red.

A long

beep

Replace the battery

with fully charged

one.

E04 Overload protection The tool automatically stops to

protect against a continuous

overcurrent.

The LED indicator



green alternately.

A series

of short

beeps

Remove the cause

of overload and

restart the tool. If

no improvement

is found, ask your

local Makita Service

Center for repair.

E05 Overheat protection The motor or controller gen-

erates excessive heat, and

the tool stops automatically to

protect the tool from damage.

The LED indicator



in red.

A series

of short

beeps

Remove the battery

cartridge immedi-

ately and cool the

tool down.

E06 Motor lock Motor lock has occurred, and

the tool automatically stops the

motor operation.

The LED indicator



green alternately.

A series

of short

beeps

Release the switch

trigger and pull it

again.

E07 Motor or controller

failure detection

Motor or controller failure has

been detected, and the tool

automatically stops the motor

operation.

The LED indicator



green alternately.

A series

of short

beeps

Ask your local

Makita Service

Center for repair.

E09 Torque sensor failure

detection

The torque sensor cannot

be monitored properly for a

number of technical reasons

including line breaks.

The LED indicator



green alternately.

A series

of short

beeps

Remove the battery

cartridge and cool

the tool down. If the

indicator remains lit,

ask your local Makita

Service Center for

repair.

-Auto-stop with fasten-

ing completion

The tool automatically stops the

motor operation after the pre-

set fastening steps have been

completed.

The LED indicator

lights up in green

for approximately

one second.

- -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DFT060T Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info