Bedienungsanleitung Makita DFT085F (Seite 8 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691722

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

8 ENGLISH

Adjusting the fastening torque

When you wish to drive machine screws, hex bolts,

etc. with the predetermined torque, adjust the fastening

torque as follows.

1. First remove the battery cartridge from the tool.

2. Loosen and remove the screw that secures ring.

3. Rotate the ring in the front of the tool by hand so

that a hole can be seen below the ring.

4. Install the battery cartridge in place. Pull the

switch trigger and release it so that the adjust ring

rotates and the hole becomes visible. And then remove

the battery cartridge.

► Fig.7: 1. Ring 2. Screw 3. Hole

5. Use an optional adjust grip to adjust the fastening

torque. Insert the pin of the adjust grip into the hole

in the front of the tool. And then, turn the adjust grip

clockwise to set a greater fastening torque, and coun-

terclockwise to set a smaller fastening torque.

6. Align the yellow line with your desired number on

the fastening torque scale.

► Fig.8: 1. Adjust grip 2. Hole for adjust grip 3. Scale

4. Yellow line

7. Insert the battery cartridge and be sure that a

fastening torque has been set up by using a fastening

torque tester.

8. Rotate the ring in front of the tool and then tighten

the screw to secure the ring.

NOTE: Numbers on the fastening torque scale is a

guideline to set up your desired fastening torque.

Adjusting no-load speed and

revolution angle etc.

You can adjust the no-load speed, number of turn, etc. of the

tool with your computer. Install the application software in

your computer and connect it to the tool with an USB cable.

► Fig.9: 1. USB port 2. USB cover 3. USB cable

NOTICE: Make sure that the USB cover closed

when fastening.

NOTE: For the application software, please contact

Makita sales representative.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/

socket bit

► Fig.10

Use only driver bit/socket bit that has inserting portion

shown in the gure. Do not use any other driver bit/

socket bit.

For tool with shallow driver bit hole

A=12mm

B=9mm

Use only these type of driver

bit. Follow the procedure

1. (Note) Bit-piece is not

necessary.

For tool with deep driver bit hole

A=17mm

B=14mm

To install these types of driver

bits, follow the procedure 1.

A=12mm

B=9mm

To install these types of driver

bits, follow the procedure 2.

(Note) Bit-piece is necessary

for installing the bit.

► Fig.11: 1. Driver bit 2. Sleeve

To install the driver bit, pull the sleeve in the direction of

the arrow and insert the driver bit into the sleeve as far

as it will go.

Then release the sleeve to secure the driver bit.

To remove the driver bit, pull the sleeve in the direction

of the arrow and pull the driver bit out.

NOTE: If the driver bit is not inserted deep enough

into the sleeve, the sleeve will not return to its original

position and the driver bit will not be secured. In this

case, try re-inserting the bit according to the instruc-

tions above.

NOTE: When it is difcult to insert the driver bit, pull

the sleeve and insert it into the sleeve as far as it will

go.

NOTE: After inserting the driver bit, make sure that it

is rmly secured. If it comes out, do not use it.

Installing hook

Optional accessory

The hook is useful to hang the tool. Install the hook to

the holes on the tool body.

► Fig.12: 1. Hook 2. Hole

OPERATION

Screwdriving operation

CAUTION: Make sure that the bit is inserted

straight in the screw head, or the screw and/or bit

may be damaged.

Place the point of the driver bit in the screw head and

apply pressure to the tool. Then switch the tool on.

When the clutch cuts in, the motor will stop automati-

cally. Then release the switch trigger.

► Fig.13

Limits of fastening capacity

Use the tool within the limits of fastening capacity. If you

use the tool beyond the limits, the clutch does not work.

And the tool cannot deliver enough fastening torque.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DFT085F Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info