Bedienungsanleitung Makita DFT087FMZ (Seite 8 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

793615

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

8ENGLISH

LED indicator / Beeper

Fig.6: 1. LED indicator

LED indicator / Beeper on the tool shows the following functions.

Function Status of the tool Status of the LED indicator/beeper Action to be taken

LED indicator Beeper

Check of the LED indi-

cator, lamp and beeper

operation

When the battery car-

tridge is installed, the tool

checks for its LED indica-

tor, lamp and beeper.



next red.

(And then the lamp

comes on.)

A series of very short

beeps

–

Detection of switch

trigger operation when

installing battery

When the battery cartridge

is installed with the switch

trigger pulled, the tool stops

to avoid unintentional start.

Blinks in red and green

alternatively.

A series of short beeps Release the switch

trigger.

Auto-stop with fastening

completion

The tool setting has

been achieved and the

tool has stopped.

Lights up in green for

approximately one

second.

– –

󰀩-

cient fastening

The tool has not completed

the tool setting because the

switch trigger has released

before reaching the set val-

ues. Otherwise, the settings

of "Failure Criteria for Phase"

has been achieved.

Lights up in red. A long beep Retighten the screw.

Intermission between

the phases

The tool is in the inter-



by the setting of "Shift to

the next Phase".

Lights up or blinks in

green (depending on

settings)

– –

Double-hitting detection

When the operator starts

to re-fasten an already-fas-

tened screw, the tool detect

it and stops.

Lights up in red. A long beep –

Alarm for low battery

capacity

The battery power became

low and it is time to replace

the battery cartridge.

Blinks in red slowly. A series of long beeps Replace the battery with

fully charged one.

Auto-stop with low

remaining battery

capacity

The battery power is

almost used up and the

tool stopped.

Lights up in red. A long beep Replace the battery with

fully charged one.

Anti-reset of controller

The battery voltage dropped

abnormally for some reason,

and the tool stopped.

Blinks in red and green

alternatively.

A series of short beeps Replace the battery with

fully charged one.

Overload protection An abnormally high



through the controller

and the tool stopped.

Blinks in red and green

alternatively.

A series of short beeps

Remove the cause of

overload and restart the

tool. If no improvement is

found, ask your local Makita

Service Center for repair.

Overheat protection The motor or the control-

ler heated up abnormally

and the tool stopped.

Blinks in red quickly. A series of short beeps Remove the battery car-

tridge immediately and

cool the tool down.

Failure to detect heat

of motor

The detection unit of

the motor fails to detect

the heat because the

cord has broken or other

reasons.

Blinks in red quickly. A series of short beeps

Remove the battery cartridge

and cool the tool down. If the

indicator does not stop, ask

your local Makita Service

Center for repair.

Motor or controller failure

detection

Motor or controller failure

has been detected. At this

time, tool does not work.

Blinks in red and green

alternatively.

A series of short beeps Ask your local Makita

Service Center for repair.

Maintenance alarm

A maintenance time has

come according to your pre-

set number of screws driven.

Blinks in yellow. –Reset the alarm with the

application software.

Alarm for unavailable data

communication (with the

tool in connection with PC)

Data cannot be exchanged

between the tool and PC in

spite of the connection.

Blinks in yellow. –Restart the application

software and re-connect

the USB cable.

Indication that data com-

munication is available

(with the tool in connec-

tion with PC)

The tool is connected to

PC and data communi-

cation is available.

Blinks in green. – –

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DFT087FMZ Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info