793614
10
Zoom out
Zoom in
Vorherige Seite
1/124
Nächste Seite
10 ENGLISH
Error code
and status
symbol on
screen
Tool performance
and function
Tool status LED indicators/beeper status Action to be taken
LED indicators Beeper
-󰀩
fastening
The tool raises an alert for
incomplete fastening under the
following operating conditions.
(1): The trigger switch is
released before the pre-set
fastening torque has been
achieved.
(2): The tool stops automati-
cally after classifying fastening
errors.
(1): The LED
indicator lights
up in red for
approximately two
seconds.
(2): The LED

in yellow and red
alternately for
approximately two
seconds.
A long
beep
Retighten the screw.
Waiting function
between pre-set
fastening steps
The tool is sitting idle, after one
of the pre-set fastening steps
has been completed, waiting to
follow the next pre-set fasten-
ing step.
* A status symbol ( 
in the display screen.
The LED indicator
lights up in green.
- -
-Low-battery alert The battery is becoming low on
power, and the battery cartridge
needs to be recharged or
replaced with fully charged one.
The LED indicator

in red.
A series of
long beeps
Replace the battery
with fully charged
one.
-Error alert for heat
detection of motor
The motor temperature cannot
be monitored properly for a
number of technical reasons
including line breaks.
The LED indicator

in red.
A series
of short
beeps
Remove the battery
cartridge and cool
the tool down. If the
indicator remains lit,
ask your local Makita
Service Center for
repair.
Maintenance notice Maintenance notice will be
posted for optimum operational
reliability when the accu-
mulated maintenance count
reaches the pre-set number.
* A status symbol ( )
appears in the display screen
when the accumulated mainte-
nance count reaches the pre-
set “Stop Count” number.
The LED indicator

-Reset the mainte-
nance count in the
application software
designed for this
tool.
Alert for storage
disabled
Up to 1,000 fastening result
data can be saved in the tool
memory. The number of unread
data in the memory reaches to
the maximum.
* A status symbol ( )
appears in the display screen
when the storage capacity
reaches the maximum.
The LED indicator

-Load the fastening
result data saved
in the tool memory
using the application
software designed
for this tool.
-Error alert for data
communication with
computer
The tool raises an alert for
communication error in the
wired environment.
The LED indicator

-Link the tool again
with the application
software designed
for the tool after
restarting the
application.
-Status indicator for
data communication
with computer
The tool informs that data
communication has been
securely established in the
wired environment.
The LED indicator

- -
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita DFT120T wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info