Bedienungsanleitung Makita DGA405 (Seite 12 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600437

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

WARNING:

• When using an abrasive cut-off/diamond wheel, be

sure to use only the special wheel guard designed for

use with cut-off wheels. (In some European countries,

when using a diamond wheel, the ordinary guard can

be used. Follow the regulations in your country.)

• NEVER use cut-off wheel for side grinding.

• Do not “jam” the wheel or apply excessive pressure. Do

not attempt to make an excessive depth of cut.

Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the

cut and the possibility of kickback, wheel breakage and

overheating of the motor may occur.

• Do not start the cutting operation in the workpiece. Let

the wheel reach full speed and carefully enter into the

cut moving the tool forward over the workpiece surface.

The wheel may bind, walk up or kickback if the power

tool is started in the workpiece.

• During cutting operations, never change the angle of

the wheel. Placing side pressure on the cut-off wheel

(as in grinding) will cause the wheel to crack and break,

causing serious personal injury.

• A diamond wheel shall be operated perpendicular to

the material being cut.

Operation with wire cup brush (optional

accessory)

CAUTION:

• Check operation of brush by running tool with no load,

insuring that no one is in front of or in line with brush.

• Do not use brush that is damaged, or which is out of

balance. Use of damaged brush could increase

potential for injury from contact with broken brush

wires.

Remove the battery cartridge from the tool and place it

upside down allowing easy access to spindle. Remove

any accessories on spindle. Thread wire cup brush onto

spindle and tighten with supplied wrench. When using

brush, avoid applying too much pressure which causes

over bending of wires, leading to premature breakage.

(Fig. 21)

Operation with wire wheel brush (optional

accessory)

CAUTION:

• Check operation of wire wheel brush by running tool

with no load, insuring that no one is in front of or in line

with the wire wheel brush.

• Do not use wire wheel brush that is damaged, or which

is out of balance. Use of damaged wire wheel brush

could increase potential for injury from contact with

broken wires.

• ALWAYS use guard with wire wheel brushes, assuring

diameter of wheel fits inside guard. Wheel can shatter

during use and guard helps to reduce chances of

personal injury.

Remove the battery cartridge from the tool and place it

upside down allowing easy access to spindle. Remove

any accessories on spindle. Thread wire wheel brush onto

spindle and tighten with the wrenches. (Fig. 22)

When using wire wheel brush, avoid applying too much

pressure which causes over bending of wires, leading to

premature breakage.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

The tool and its air vents have to be kept clean. Regularly

clean the tool’s air vents or whenever the vents start to

become obstructed. (Fig. 23)

Remove the dust cover from inhalation vent and clean it

for smooth air circulation. (Fig. 24)

NOTE:

• Clean out the dust cover when it is clogged with dust or

foreign matters. Continuing operation with a clogged

dust cover may damage the tool.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Makita genuine battery and charger

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DGA405 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info