Bedienungsanleitung Makita DGA456 (Seite 13 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691735

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

13 ENGLISH

For 115 mm (4 - 1/2″) / 125 mm (5″)

model

► Fig.15: 1. Sanding lock nut 2. Abrasive disc

3. Rubber pad

1. Mount the rubber pad onto the spindle.

2. Fit the disc on the rubber pad and screw the sand-

ing lock nut onto the spindle.

Hold the spindle with the shaft lock, and securely tighten

the sanding lock nut clockwise with the lock nut wrench.

To remove the disc, follow the installation procedure in

reverse.

OPERATION

WARNING: It should never be necessary to

force the tool. The weight of the tool applies ade-

quate pressure. Forcing and excessive pressure

could cause dangerous wheel breakage.

WARNING: ALWAYS replace wheel if tool is

dropped while grinding.

WARNING: NEVER bang or hit grinding disc

or wheel onto work.

WARNING:

Avoid bouncing and snagging the

wheel, especially when working corners, sharp edges

etc. This can cause loss of control and kickback.

WARNING: NEVER use tool with wood cutting

blades and other saw blades. Such blades when

used on a grinder frequently kick and cause loss of

control leading to personal injury.

CAUTION: Never switch on the tool when it

is in contact with the workpiece, it may cause an

injury to operator.

CAUTION: Always wear safety goggles or a

face shield during operation.

CAUTION: After operation, always switch off

the tool and wait until the wheel has come to a

complete stop before putting the tool down.

CAUTION:

ALWAYS hold the tool rmly with one

hand on housing and the other on the side handle.

Grinding and sanding operation

► Fig.16

Turn the tool on and then apply the wheel or disc to the

workpiece.

In general, keep the edge of the wheel or disc at an

angle of about 15° to the workpiece surface.

During the break-in period with a new wheel, do not

work the grinder in forward direction or it may cut into

the workpiece. Once the edge of the wheel has been

rounded off by use, the wheel may be worked in both

forward and backward direction.

Operation with abrasive cut-off /

diamond wheel

Optional accessory

WARNING: When using an abrasive cut-off

/ diamond wheel, be sure to use only the special

wheel guard designed for use with cut-off wheels.

(In some European countries, when using a diamond

wheel, the ordinary guard can be used. Follow the

regulations in your country.)

WARNING: NEVER use cut-off wheel for side

grinding.

WARNING: Do not "jam" the wheel or apply

excessive pressure. Do not attempt to make an

excessive depth of cut. Overstressing the wheel

increases the loading and susceptibility to twisting

or binding of the wheel in the cut and the possibility

of kickback, wheel breakage and overheating of the

motor may occur.

WARNING: Do not start the cutting operation

in the workpiece. Let the wheel reach full speed

and carefully enter into the cut moving the tool

forward over the workpiece surface. The wheel

may bind, walk up or kickback if the power tool is

started in the workpiece.

WARNING:

During cutting operations, never

change the angle of the wheel. Placing side pressure on

the cut-off wheel (as in grinding) will cause the wheel to

crack and break, causing serious personal injury.

WARNING: A diamond wheel shall be oper-

ated perpendicular to the material being cut.

► Fig.17: 1. Lock nut 2. Abrasive cut-off wheel / dia-

mond wheel 3. Inner ange 4. Wheel guard

for abrasive cut-off wheel / diamond wheel

As for the installation, follow the instructions for

depressed center wheel.

The direction for mounting the lock nut and the

inner ange varies by wheel type and thickness.

Refer to the following gures.

For 100 mm (4″) model

When installing the abrasive cut-off wheel:

► Fig.18: 1. Lock nut 2. Abrasive cut-off wheel

(Thinner than 4mm (5/32")) 3. Abrasive cut-

off wheel (4mm (5/32") or thicker) 4. Inner

ange

When installing the diamond wheel:

► Fig.19: 1. Lock nut 2. Diamond wheel (Thinner

than 4mm (5/32″)) 3. Diamond wheel (4mm

(5/32″) or thicker) 4. Inner ange

For 115 mm (4 - 1/2″) / 125 mm (5″)

model

When installing the abrasive cut-off wheel:

► Fig.20: 1. Lock nut 2. Abrasive cut-off wheel

(Thinner than 4mm (5/32")) 3. Abrasive cut-

off wheel (4mm (5/32") or thicker) 4. Inner

ange

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DGA456 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info