Bedienungsanleitung Makita DGA461 (Seite 19 von 188) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691744

Zoom out

Zoom in

Vorherige Seite

1/188

Nächste Seite

19 ENGLISH

► Fig.19: 1. Lock nut 2. Abrasive cut-off wheel / dia-

mond wheel 3. Inner ange 4. Wheel guard

for abrasive cut-off wheel / diamond wheel

As for the installation, follow the instructions for

depressed center wheel.

The direction for mounting the lock nut and the

inner ange varies by wheel type and thickness.

Refer to the following gures.

For 100 mm (4″) model

When installing the abrasive cut-off wheel:

► Fig.20: 1. Lock nut 2. Abrasive cut-off wheel

(Thinner than 4mm (5/32")) 3. Abrasive cut-

off wheel (4mm (5/32") or thicker) 4. Inner

ange

When installing the diamond wheel:

► Fig.21: 1. Lock nut 2. Diamond wheel (Thinner

than 4mm (5/32″)) 3. Diamond wheel (4mm

(5/32″) or thicker) 4. Inner ange

For 115 mm (4 - 1/2″) / 125 mm (5″)

model

When installing the abrasive cut-off wheel:

► Fig.22: 1. Lock nut 2. Abrasive cut-off wheel

(Thinner than 4mm (5/32")) 3. Abrasive cut-

off wheel (4mm (5/32") or thicker) 4. Inner

ange

When installing the diamond wheel:

► Fig.23: 1. Lock nut 2. Diamond wheel (Thinner

than 4mm (5/32″)) 3. Diamond wheel (4mm

(5/32″) or thicker) 4. Inner ange

Operation with wire cup brush

Optional accessory

CAUTION: Check operation of brush by run-

ning tool with no load, insuring that no one is in

front of or in line with brush.

CAUTION: Do not use brush that is damaged,

or which is out of balance. Use of damaged brush

could increase potential for injury from contact with

broken brush wires.

► Fig.24: 1. Wire cup brush

Remove the battery cartridge from the tool and place it

upside down allowing easy access to spindle.

Remove any accessories on spindle. Thread wire cup

brush onto spindle and tighten with supplied wrench.

NOTICE: Avoid applying too much pressure

which causes over bending of wires when using

brush. It may lead to premature breakage.

Operation with wire wheel brush

Optional accessory

CAUTION: Check operation of wire wheel

brush by running tool with no load, insuring that

no one is in front of or in line with the wire wheel

brush.

CAUTION: Do not use wire wheel brush that

is damaged, or which is out of balance. Use of

damaged wire wheel brush could increase potential

for injury from contact with broken wires.

CAUTION: ALWAYS use guard with wire

wheel brushes, assuring diameter of wheel ts

inside guard. Wheel can shatter during use and

guard helps to reduce chances of personal injury.

► Fig.25: 1. Wire wheel brush

Remove the battery cartridge from the tool and place it

upside down allowing easy access to spindle.

Remove any accessories on spindle. Thread wire wheel

brush onto spindle and tighten with the wrenches.

NOTICE: Avoid applying too much pressure

which causes over bending of wires when

using wire wheel brush. It may lead to premature

breakage.

WIRELESS ACTIVATION

FUNCTION

For DGA412/DGA414/DGA462/DGA464/DGA512/

DGA514 only

What you can do with the wireless

activation function

The wireless activation function enables clean and com-

fortable operation. By connecting a supported vacuum

cleaner to the tool, you can run the vacuum cleaner

automatically along with the switch operation of the tool.

► Fig.26

To use the wireless activation function, prepare follow-

ing items:

• A wireless unit

• A vacuum cleaner which supports the wireless

activation function

The overview of the wireless activation function

setting is as follows. Refer to each section for detail

procedures.

1. Installing the wireless unit

2. Tool registration for the vacuum cleaner

3. Starting the wireless activation function

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DGA461 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info