Bedienungsanleitung Makita DGA468 (Seite 15 von 184) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691755

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

15 ENGLISH

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically. In this case, remove the battery from the

tool and charge the battery.

Releasing protection lock

When the protection system works repeatedly, the tool

is locked and the battery indicator shows the following

state.

In this situation, the tool does not start even if turning

the tool off and on. To release the protection lock,

remove the battery, set it to the battery charger and wait

until the charging nishes.

Off

Blinking

Shaft lock

Press the shaft lock to prevent spindle rotation when

installing or removing accessories.

► Fig.4: 1. Shaft lock

NOTICE: Never actuate the shaft lock when the

spindle is moving. The tool may be damaged.

Switch action

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch lever actuates properly and returns to the

"OFF" position when released.

CAUTION: Do not pull the switch lever hard

without pulling the lock-off lever. This can cause

switch breakage.

CAUTION: For your safety, this tool is

equipped with lock-off lever which prevents the

tool from unintended starting. NEVER use the tool

if it runs when you simply pull the switch trigger

without pulling the lock-off lever. Return the tool

to our authorized service center for proper repairs

BEFORE further usage.

CAUTION: NEVER tape down or defeat pur-

pose and function of lock-off lever.

To prevent the switch lever from being accidentally

pulled, a lock-off lever is provided.

To start the tool, pull the lock-off lever toward the opera-

tor and then pull the switch lever.

To stop the tool, release the switch lever.

► Fig.5: 1. Lock-off lever 2. Switch lever

Speed adjusting dial

The rotation speed of the tool can be changed by turn-

ing the speed adjusting dial. The table below shows

the number on the dial and the corresponding rotation

speed.

► Fig.6: 1. Speed adjusting dial

Number Speed

1 3,000 min

-1

2 4,500 min

-1

3 6,000 min

-1

4 7,500 min

-1

5 8,500 min

-1

NOTICE: If the tool is operated continuously at

low speed for a long time, the motor will get over-

loaded, resulting in tool malfunction.

NOTICE: When changing the speed dial from "5"

to "1", turn the dial counterclockwise. Do not turn

the dial clockwise forcibly.

Automatic speed change function

► Fig.7: 1. Mode indicator

Mode indicator status Operation mode

High speed mode

High torque mode

This tool has "high speed mode" and "high torque

mode". It automatically changes operation mode

depending on the work load. When mode indicator

lights up during operation, the tool is in high torque

mode.

Accidental re-start preventive

function

Even if installing the battery cartridge while pulling the

switch lever, the tool does not start.

To start the tool, rst release the switch lever. Then pull

the lock-off lever, and pull the switch lever.

Electronic torque control function

The tool electronically detects situations where the

wheel or accessory may be at risk to be bound. In the

situation, the tool is automatically shut off to prevent

further rotation of the spindle (it does not prevent

kickback).

To restart the tool, switch off the tool rst, remove the

cause of sudden drop in the rotation speed, and then

turn the tool on.

Soft start feature

Soft start feature reduces starting reaction.

Electric brake

Electric brake is activated after the tool is switched off.

The brake does not work when the power supply is shut

down, such as the battery is removed accidentally, with

the switch still on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DGA468 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info