Bedienungsanleitung Makita DGA505 (Seite 10 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600439

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

015096

Automatic speed change function (Fig. 4)

015098

This tool has “high speed mode” and “high torque mode”.

It automatically changes operation mode depending on

the work load. When mode indicator lights up during

operation, the tool is in high torque mode.

Tool/battery protection system

The tool is equipped with a tool/battery protection system.

This system automatically cuts off power to the motor to

extend tool and battery life.

The tool will automatically stop during operation if the tool

or battery is placed under one of the following conditions.

In some conditions, the indicator lights up.

Overload protection

When the tool is operated in a manner that causes it to

draw an abnormally high current, the tool automatically

stops without any indications. In this situation, turn the tool

off and stop the application that caused the tool to

become overloaded. Then turn the tool on to restart.

Overheat protection for tool

When the tool is overheated, the tool stops automatically

and the battery indicator shows following state. In this

situation, let the tool cool before turning the tool on again.

015140

Releasing protection lock

When the protection system works repeatedly, the tool is

locked and the battery indicator shows the following state.

015200

In this situation, the tool does not start even if turning the

tool off and on. To release the protection lock, remove the

battery, set it to the battery charger and wait until the

charging finishes.

Shaft lock

CAUTION:

• Never actuate the shaft lock when the spindle is

moving. The tool may be damaged.

Press the shaft lock to prevent spindle rotation when

installing or removing accessories. (Fig. 5)

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing side grip (handle)

CAUTION:

• Always be sure that the side grip is installed securely

before operation.

Screw the side grip securely on the position of the tool as

shown in the figure. (Fig. 6)

Installing or removing wheel guard (For

depressed center wheel, flap disc/

abrasive cut-off wheel, diamond wheel)

WARNING:

• When using a depressed center grinding wheel/flap

disc, flex wheel, wire wheel brush, cut-off wheel or

diamond wheel, the wheel guard must be fitted on the

tool so that the closed side of the guard always points

toward the operator.

• When using an abrasive cut-off/diamond wheel, be

sure to use only the special wheel guard designed for

use with cut-off wheels. (In some European countries,

when using a diamond wheel, the ordinary guard can

be used. Follow the regulations in your country.)

For tool with clamp lever type wheel guard

Loosen the lever on the wheel guard after loosening the

screw. Mount the wheel guard with the protrusion on the

wheel guard band aligned with the notch on the bearing

box. Then rotate the wheel guard to such an angle that it

can protect the operator according to work. (Fig. 7)

Tighten the lever to fasten the wheel guard. If the lever is

too tight or too loose to fasten the wheel guard, loosen or

tighten the screw to adjust the tightening of the wheel

guard band. (Fig. 8)

To remove wheel guard, follow the installation procedure

in reverse.

Battery indicator status

Remaining battery

capacity

: On : Off : Blinking

50% - 100%

20% - 50%

0% - 20%

Charge the battery

Mode indicator status Operation mode

High speed mode

High torque mode

Battery indicator : On : Off : Blinking

Tool is overheated

Battery indicator : On : Off : Blinking

Protection lock works

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DGA505 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info