Bedienungsanleitung Makita DGD801 (Seite 7 von 14) (Englisch, Holländisch)

600447

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing wheel point (Fig. 5 & 6)

Loosen the collet nut and insert the wheel point into the

collet nut. Use one wrench to hold the spindle and the

other one to tighten the collet nut securely.

The wheel point should not be mounted more than 8 mm

from the collet nut. Exceeding this distance could cause

vibration or a broken shaft.

To remove the wheel point, follow the installation proce-

dure in reverse.

CAUTION:

• Use the correct size collet cone for the wheel point

which you intend to use.

OPERATION (Fig. 7)

Turn the tool on without the wheel point making any con-

tact with the workpiece and wait until the wheel point

attains full speed. Then apply the wheel point to the

workpiece gently. To obtain a good finish, move the tool

in the leftward direction slowly.

CAUTION:

• Apply light pressure on the tool. Excessive pressure on

the tool will only cause a poor finish and overloading of

the motor.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before attempting to perform

inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing carbon brushes

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes. (Fig. 8)

Insert the top end of slotted bit screwdriver into the notch

in the tool and remove the holder cap cover by lifting it

up. (Fig. 9)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps. (Fig. 10)

Reinstall the holder cap cover on the tool.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

Side handle (accessory) (Fig. 11, 12, 13 & 14)

When using the side handle, remove the rubber protec-

tor, insert the side handle on the tool barrel as far as it

will go and rotate it to the desired angle. Then tighten the

handle firmly by turning clockwise.

CAUTION:

• When using the tool without handle, always install the

rubber protector on the tool.

• When installing the rubber protector, always push it

onto the tool so that the top round recessed shape of

the rubber is positioned near the switch position.

• Wheel points

• Collet cone (3 mm, 6 mm, 8 mm, 1/4", 1/8")

•Collet nut

• Wrench 13

• Side handle set

• Makita genuine battery and charger

NOTE:

• Some items in the list may be included in the tool pack-

age as standard accessories. They may differ from

country to country.

ENG905-1

Noise

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 72 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Model DGD800

Work mode: surface grinding

Vibration emission (a

h, SG

): 6.5 m/s

Uncertainty (K): 1.5 m/s

Model DGD801

Work mode: surface grinding

Vibration emission (a

h, SG

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been mea-

sured in accordance with the standard test method and

may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the oper-

ator that are based on an estimation of exposure in the

actual conditions of use (taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to

the trigger time).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DGD801 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info