Bedienungsanleitung Makita DHP459 (Seite 6 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

597290

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Switch action (Fig. 3)

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

Lighting up the lamp (Fig. 4)

CAUTION:

• Do not look in the light or see the source of light

directly.

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

The lamp goes out just after releasing the trigger.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of the lamp.

Be careful not to scratch the lens of lamp, or it may

lower the illumination.

Reversing switch action (Fig. 5)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for counter-

clockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

Speed change (Fig. 6)

CAUTION:

• Always set the speed change lever fully to the correct

position. If you operate the tool with the speed change

lever positioned halfway between the “1” side and “2”

side, the tool may be damaged.

• Do not use the speed change lever while the tool is

running. The tool may be damaged.

To change the speed, first switch off the tool and then

slide the speed change lever to the “2” side for high

speed or “1” side for low speed. Be sure that the speed

change lever is set to the correct position before opera-

tion. Use the right speed for your job.

Selecting the action mode (Fig. 7)

This tool employs an action mode changing ring. Select

one of the three modes suitable for your work needs by

using this ring.

For rotation only, turn the ring so that the arrow on the

tool body points toward the m mark on the ring.

For rotation with hammering, turn the ring so that the

arrow points toward the g mark on the ring.

For rotation with clutch, turn the ring so that the arrow

points toward the mark on the ring.

CAUTION:

• Always set the ring correctly to your desired mode

mark. If you operate the tool with the ring positioned

halfway between the mode marks, the tool may be

damaged.

Adjusting the fastening torque (Fig. 7)

The fastening torque can be adjusted in 16 steps by turn-

ing the adjusting ring so that the graduations are aligned

with the arrow on the tool body. The fastening torque is

minimum when the number 1 is aligned with the arrow,

and maximum when the number 16 is aligned with the

arrow.

Before the actual operation, drive a trial screw into your

material or a piece of duplicate material to determine

which torque level is required for a particular application.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing the driver bit or drill bit

(Fig. 8)

Turn the sleeve counterclockwise to open the chuck

jaws. Place the bit in the chuck as far as it will go. Turn

the sleeve clockwise to tighten the chuck.

To remove the bit, turn the sleeve counterclockwise.

Installing the hook (Fig. 9)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool hous-

ing on either side and then secure it with a screw. To

remove, loosen the screw and then take it out.

Installing the bit holder (Optional accessory)

(Fig. 10)

Fit the bit holder into the protrusion at the tool foot on

either right or left side and secure it with a screw.

When not using the driver bit, keep it in the bit holders.

Bits 45 mm long can be kept there.

OPERATION

CAUTION:

• Always insert the battery cartridge all the way until it

locks in place. If you can see the red part on the upper

side of the button, it is not locked completely. Insert it

fully until the red part cannot be seen. If not, it may

accidentally fall out of the tool, causing injury to you or

someone around you.

Hold the tool firmly with one hand on the grip and the

other hand on the bottom of the battery cartridge to con-

trol the twisting action.

CAUTION:

• Do not cover vents, or it may cause overheating and

damage to the tool. (Fig. 11)

Hammer drilling operation

CAUTION:

• There is a tremendous and sudden twisting force

exerted on the tool/bit at the time of hole break-

through, when the hole becomes clogged with chips

and particles, or when striking reinforcing rods embed-

ded in the concrete.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DHP459 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info