Bedienungsanleitung Makita DHR182 (Seite 20 von 152) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691040

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

20 ENGLISH

Wheninsertingthewirelessunit,aligntheprojections

with the recessed portions on the slot.

►Fig.45: 1. Wireless unit 2.Projection3. Lid

4. Recessed portion

When removing the wireless unit, open the lid slowly.

Thehooksonthebackofthelidwillliftthewirelessunit

as you pull up the lid.

►Fig.46: 1. Wireless unit 2. Hook 3. Lid

Afterremovingthewirelessunit,keepitinthesupplied

case or a static-free container.

NOTICE: Always use the hooks on the back of

the lid when removing the wireless unit. If the

hooks do not catch the wireless unit, close the lid

completely and open it slowly again.

Tool registration for the vacuum

cleaner

NOTE:

AMakitavacuumcleanersupportingthewireless

activation function is required for the tool registration.

NOTE: Finish installing the wireless unit to the tool

before starting the tool registration.

NOTE:

During the tool registration, do not pull the switch

trigger or turn on the power switch on the vacuum cleaner.

NOTE: Refer to the instruction manual of the vacuum

cleaner, too.

If you wish to activate the vacuum cleaner along with

theswitchoperationofthetool,nishthetoolregistra-

tion beforehand.

Install the batteries to the vacuum cleaner and the tool.

2. Set the stand-by switch on the vacuum cleaner to

"AUTO".

►Fig.47: 1. Stand-by switch

3. Press the wireless activation button on the vac-

uum cleaner for 3 seconds until the wireless activation

lampblinksingreen.Andthenpressthewirelessacti-

vation button on the tool in the same way.

►Fig.48: 1. Wireless activation button 2. Wireless

activation lamp

If the vacuum cleaner and the tool are linked success-

fully, the wireless activation lamps will light up in green

for 2 seconds and start blinking in blue.

NOTE:Thewirelessactivationlampsnishblinking

in green after 20 seconds elapsed. Press the wireless

activation button on the tool while the wireless acti-

vation lamp on the cleaner is blinking. If the wireless

activation lamp does not blink in green, push the wire-

lessactivationbuttonbrieyandholditdownagain.

NOTE: When performing two or more tool registra-

tionsforonevacuumcleaner,nishthetoolregistra-

tion one by one.

Starting the wireless activation

function

NOTE: Finish the tool registration for the vacuum

cleaner prior to the wireless activation.

NOTE: Refer to the instruction manual of the vacuum

cleaner, too.

Afterregisteringatooltothevacuumcleaner,the

vacuum cleaner will automatically runs along with the

switch operation of the tool.

1. Install the wireless unit to the tool.

2. Connect the hose of the vacuum cleaner with the

tool.

►Fig.49

3. Set the stand-by switch on the vacuum cleaner to

"AUTO".

►Fig.50: 1. Stand-by switch

4. Push the wireless activation button on the tool

briey.Thewirelessactivationlampwillblinkinblue.

►Fig.51: 1. Wireless activation button 2. Wireless

activation lamp

5. Pull the switch trigger of the tool. Check if the

vacuum cleaner runs while the switch trigger is being

pulled.

Tostopthewirelessactivationofthevacuumcleaner,

push the wireless activation button on the tool.

NOTE:Thewirelessactivationlamponthetoolwill

stop blinking in blue when there is no operation for

2 hours. In this case, set the stand-by switch on the

vacuumcleanerto"AUTO"andpushthewireless

activation button on the tool again.

NOTE:Thevacuumcleanerstarts/stopswithadelay.

Thereisatimelagwhenthevacuumcleanerdetects

a switch operation of the tool.

NOTE:Thetransmissiondistanceofthewirelessunit

may vary depending on the location and surrounding

circumstances.

NOTE: When two or more tools are registered to one

vacuum cleaner, the vacuum cleaner may start run-

ning even if you don't pull the switch trigger because

an other user is using the wireless activation function.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DHR182 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info