Bedienungsanleitung Makita DHS630 (Seite 9 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600424

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Bevel cutting (Fig. 11)

Loosen the wing screw on the front and rear base. Set for

the desired angle (0° - 45°) by tilting accordingly, then

tighten the wing screw securely.

Sighting (Fig. 12)

For straight cuts, align the 0° position on the front of the

base with your cutting line. For 45° bevel cuts, align the

45° position with it. The position of the top guide is

adjustable.

Switch action (Fig. 13)

CAUTION:

• Before installing the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

• Do not pull the switch trigger hard without pressing the

lock-off lever. This can cause switch breakage.

To prevent the switch trigger from being accidentally

pulled, a lock-off lever is provided. To start the tool, press

the lock-off lever and pull the switch trigger. Release the

switch trigger to stop.

WARNING:

• For your safety, this tool is equipped with lock-off lever

which prevents the tool from unintended starting.

NEVER use the tool if it runs when you simply pull the

switch trigger without pressing the lock-off lever.

Return tool a MAKITA service center for proper repairs

BEFORE further usage.

• NEVER tape down or defeat purpose and function of

lock-off lever.

Lighting the lamp

CAUTION:

• Do not look in the light or see the source of light

directly. (Fig. 14)

Only to turn on the light, pull the switch trigger without

pressing the lock-off lever. To turn on the light and run the

tool, press the lock-off lever and pull the switch trigger

with the lock-off lever being pressed.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

• Do not use gasoline, thinner or the like to clean the lens

of lamp. Using such substances will damage the lens.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Removing or installing saw blade

CAUTION:

• Be sure the blade is installed with teeth pointing up at

the front of the tool.

• Use only the Makita wrench to install or remove the

blade. (Fig. 15)

To remove the blade, press the shaft lock so that the

blade cannot revolve and use the wrench to loosen the

hex bolt counterclockwise. Then remove the hex bolt,

outer flange and blade.

To install the blade, follow the removal procedure in

reverse. BE SURE TO TIGHTEN THE HEX BOLT

CLOCKWISE SECURELY. (Fig. 16)

When changing blade, make sure to also clean upper and

lower blade guards of accumulated sawdust. Such efforts

do not, however, replace the need to check lower guard

operation before each use.

Hex wrench storage (Fig. 17)

When not in use, store the hex wrench as shown in the

figure to keep it from being lost.

Connecting a vacuum cleaner (for

European countries only) (Fig. 18 & 19)

When you wish to perform clean cutting operation,

connect a Makita vacuum cleaner to your tool. Install the

dust nozzle on the tool using the screw. Then connect a

hose of the vacuum cleaner to the dust nozzle as shown

in the figure.

OPERATION

CAUTION:

• Always insert the battery cartridge all the way until it

locks in place. If you can see the red part on the upper

side of the button, it is not locked completely. Insert it

fully until the red part cannot be seen. If not, it may

accidentally fall out of the tool, causing injury to you or

someone around you.

• Be sure to move the tool forward in a straight line

gently. Forcing or twisting the tool will result in

overheating the motor and dangerous kickback,

possibly causing severe injury.

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

15 minutes before proceeding with a fresh battery.

(Fig. 20)

Hold the tool firmly. The tool is provided with both a front

grip and rear handle. Use both to best grasp the tool. If

both hands are holding saw, they cannot be cut by the

blade. Set the base on the workpiece to be cut without the

blade making any contact. Then turn the tool on and wait

until the blade attains full speed. Now simply move the

tool forward over the workpiece surface, keeping it flat

and advancing smoothly until the sawing is completed.

To get clean cuts, keep your sawing line straight and your

speed of advance uniform. If the cut fails to properly follow

your intended cut line, do not attempt to turn or force the

tool back to the cut line. Doing so may bind the blade and

lead to dangerous kickback and possible serious injury.

Release switch, wait for blade to stop and then withdraw

tool. Realign tool on new cut line, and start cut again.

Attempt to avoid positioning which exposes operator to

chips and wood dust being ejected from saw. Use eye

protection to help avoid injury.

Rip fence (Guide rule) (Fig. 21)

The handy rip fence allows you to do extra-accurate

straight cuts. Simply slide the rip fence up snugly against

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DHS630 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info