Bedienungsanleitung Makita DHS680 (Seite 9 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600423

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

properly and returns to the “OFF” position when

released.

• Do not pull the switch trigger hard without pressing the

lock-off lever. This can cause switch breakage. (Fig. 9)

To prevent the switch trigger from being accidentally

pulled, a lock-off lever is provided. To start the tool, press

the lock-off lever and pull the switch trigger. Release the

switch trigger to stop.

WARNING:

• For your safety, this tool is equipped with lock-off lever

which prevents the tool from unintended starting.

NEVER use the tool if it runs when you simply pull the

switch trigger without pressing the lock-off lever. Return

tool to a MAKITA service center for proper repairs

BEFORE further usage.

• NEVER tape down or defeat purpose and function of

lock-off lever.

Indicating remaining battery capacity

(Fig. 10)

When you turn the tool on, the battery indicator shows the

remaining battery capacity.

The remaining battery capacity is shown as the following

table.

015146

Automatic speed change function

(Fig. 11)

015137

This tool has “high speed mode” and “high torque mode”.

It automatically changes operation mode depending on

the work load. When mode indicator lights up during

operation, the tool is in high torque mode.

Tool/battery protection system

The tool is equipped with a tool/battery protection system.

This system automatically cuts off power to the motor to

extend tool and battery life.

The tool will automatically stop during operation if the tool

or battery are placed under one of the following

conditions. In some conditions, the indicator lights up.

Overload protection

When the tool is operated in a manner that causes it to

draw an abnormally high current, the tool automatically

stops without any indications. In this situation, turn the tool

off and stop the application that caused the tool to

become overloaded. Then turn the tool on to restart.

Overheat protection for tool

When the tool is overheated, the tool stops automatically

and the battery indicator shows following state. In this

situation, let the tool cool before turning the tool on again.

015145

Releasing protection lock

When the protection system works repeatedly, the tool is

locked and the battery indicator shows the following state.

015201

In this situation, the tool does not start even if turning the

tool off and on. To release the protection lock, remove the

battery, set it to the battery charger and wait until the

charging finishes.

Adjusting depth of cut

CAUTION:

• After adjusting the depth of cut, always tighten the lever

securely.

Loosen the lever on the side of the rear handle and move

the base up or down. At the desired depth of cut, secure

the base by tightening the lever. (Fig. 12)

For cleaner, safer cuts, set cut depth so that no more than

one blade tooth projects below workpiece. Using proper

cut depth helps to reduce potential for dangerous

KICKBACKS which can cause personal injury.

Bevel cutting

Loosen the front lever. Set for the desired angle (0° - 50°)

by tilting accordingly, then tighten the front lever securely.

(Fig. 13)

Use the 45° stopper when you do precise 45° angle

cutting. Turn the stopper counterclockwise fully for bevel

cut (0° - 45°) and turn it clockwise for 0° - 50° bevel cuts.

(Fig. 14)

Battery indicator status

Remaining battery

capacity

: On : Off : Blinking

50% - 100%

20% - 50%

0% - 20%

Charge the battery

Mode indicator status Operation mode

High speed mode

High torque mode

Battery indicator : On : Off : Blinking

Tool is overheated

Battery indicator : On : Off : Blinking

Protection lock works

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DHS680 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info