Bedienungsanleitung Makita DJR185 (Seite 9 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600415

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

straight into the blade clamp and tighten it by hex wrench.

Pull the saw blade lightly to make sure that the saw blade

does not fall off during operation.

To remove the saw blade, follow the installation procedure

in reverse.

Hex wrench storage (Fig. 13)

When not in use, store the hex wrench as shown in the

figure to keep it from being lost.

OPERATION

CAUTION:

• Always press the shoe firmly against the workpiece

during operation. If the shoe is held away from the

workpiece during operation, strong vibration and/or

twisting will be produced, causing the blade to snap

dangerously.

• Always wear gloves to protect your hands from hot

flying chips when cutting metal.

• Be sure to always wear suitable eye protection which

conforms with current national standards.

• Always use a suitable coolant (cutting oil) when cutting

metal. Failure to do so will cause premature blade

wear. (Fig. 14)

Press the shoe firmly against the workpiece. Do not allow

the tool to bounce. Bring the saw blade into light contact

with the workpiece. First, make a pilot groove using a

slower speed. Then use a faster speed to continue

cutting. (Fig. 15 & 16)

• You can use the switch lever or trigger according to

your work.

NOTE:

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

15 minutes before proceeding with a fresh battery.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Recipro saw blades

• Jig saw blades (only for Model DJR145, DJR185)

• Makita genuine battery and charger

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ from

country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Model DJR143, DJR185

Sound pressure level (L

): 76 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Model DJR145, DJR183

Sound pressure level (L

): 77 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Model DJR143, DJR145

Work mode: cutting boards

Vibration emission (a

h, B

): 7.0 m/s

Uncertainty (K): 1.5 m/s

Work mode: cutting wooden beams

Vibration emission (a

h, WB

): 7.0 m/s

Uncertainty (K): 1.5 m/s

Model DJR183, DJR185

Work mode: cutting boards

Vibration emission (a

h, B

): 8.0 m/s

Uncertainty (K): 1.5 m/s

Work mode: cutting wooden beams

Vibration emission (a

h, WB

): 7.0 m/s

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

For European countries only

ENH101-17

EC Declaration of Conformity

Makita declares that the following Machine(s):

Designation of Machine:

Cordless Recipro Saw

Model No./Type: DJR143, DJR145, DJR183, DJR185

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DJR185 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info